Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
62720A
1.INSTALL QUARTER WINDOW ASSEMBLY LH
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Allow the primer coating to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Using a brush or sponge, apply Primer G to the contact surface of the glass.
If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Apply adhesive to the quarter window glass.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the quarter window glass as shown in the illustration.
Install the quarter window glass to the vehicle body.
Hold the quarter window glass securely in place with protective tape or equivalent until the adhesive hardens.
Allow the primer coating to dry for 3 minutes or more.
Check that the clips are attached to the body correctly.
Check the clearance between the body and glass.
Lightly press the front surface of the glass to ensure a close fit.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive onto the glass rim.
Do not drive the vehicle within the time written in the table below.
| Temperature | Minimum time prior to driving vehicle |
|---|---|
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
Connect the 2 connectors.
62720A
2.CHECK FOR LEAKS AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
62452C
3.INSTALL REAR ROOF SIDE RAIL GARNISH LH
62472A
4.INSTALL INNER ROOF SIDE GARNISH LH
62639A
5.INSTALL QUARTER PILLAR GARNISH LH (for Except Captain Seat Type)
62639A
6.INSTALL QUARTER PILLAR GARNISH LH (for Captain Seat Type)
64740A
7.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Except Captain Seat Type)
64740A
8.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Captain Seat Type)
64766
9.INSTALL QUARTER TRIM JACK COVER SUB-ASSEMBLY (for LH Side)
64735G
10.INSTALL DECK TRIM SIDE SERVICE HOLE COVER LH
66311B
11.INSTALL ROPE HOOK
58625D
12.INSTALL REAR FLOOR NO. 1 MAT PLATE (for Power Stowing Seat Type)
58625D
13.INSTALL REAR FLOOR NO. 1 MAT PLATE (for Tumble Seat Type, Manual Stowing Seat Type)
67935
14.INSTALL BACK DOOR SCUFF PLATE
67881A
15.INSTALL BACK DOOR WEATHERSTRIP
72906
16.INSTALL 3RD SEAT LINK SUB-ASSEMBLY (for Manual Stowing Seat Type LH Side)
17.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Manual Stowing Seat Type LH Side)
79273
18.INSTALL NO. 2 SEAT HINGE COVER (for Manual Stowing Seat Type LH Side)
79236A
19.INSTALL NO. 2 SEAT LEG COVER (for Manual Stowing Seat Type LH Side)
79236A
20.INSTALL NO. 2 SEAT LEG COVER LH (for Manual Stowing Seat Type LH Side)
79384
21.INSTALL NO. 3 SEAT LEG COVER REAR LH (for Manual Stowing Seat Type LH Side)
79040
22.INSTALL NO. 3 SEAT LEG ASSEMBLY LH (for Power Stowing Seat Type LH Side)
23.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Power Stowing Seat Type LH Side)
79273
24.INSTALL NO. 2 SEAT HINGE COVER (for Power Stowing Seat Type LH Side)
79384
25.INSTALL NO. 3 SEAT LEG COVER REAR LH (for Power Stowing Seat Type LH Side)
79236A
26.INSTALL NO. 2 SEAT LEG COVER LH (for Power Stowing Seat Type LH Side)
27.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Tumble Seat Type LH Side)
72137E
28.INSTALL NO. 1 SEAT TRACK COVER (for Tumble Seat Type LH Side)
64420A
29.INSTALL LUGGAGE ROOM BOX LID ASSEMBLY (for Tumble Seat Type, Manual Stowing Seat Type)
67872A
30.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP LH
67918E
31.INSTALL REAR DOOR SCUFF PLATE LH
67918D
32.INSTALL REAR DOOR SCUFF PLATE LH