Home › Vehicle Interior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292227 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 67918E 1.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67918E 2.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67872A 3.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH

Hide 64420A 4.REMOVE LUGGAGE ROOM BOX LID ASSEMBLY (for Tumble Seat Type, Manual Stowing Seat Type)

Hide 72137E 5.REMOVE NO. 1 SEAT TRACK COVER (for Tumble Seat Type LH Side)

Hide 6.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Tumble Seat Type LH Side)

Hide 79236B 7.REMOVE NO. 2 SEAT LEG COVER LH (for Power Stowing Seat Type LH Side)

Hide 58417H 8.REMOVE NO. 3 SEAT LEG COVER REAR LH (for Power Stowing Seat Type LH Side)

Hide 79273 9.REMOVE NO. 2 SEAT HINGE COVER (for Power Stowing Seat Type LH Side)

Hide 10.REMOVE NO. 2 SEAT ASSEMBLY REAR LH (for Power Stowing Seat Type LH Side)

Hide 79040 11.REMOVE NO. 3 SEAT LEG ASSEMBLY LH (for Power Stowing Seat Type LH Side)

Hide 79384 12.REMOVE NO. 3 SEAT LEG COVER REAR LH (for Manual Stowing Seat Type LH Side)

Hide 79236A 13.REMOVE NO. 2 SEAT LEG COVER LH (for Manual Stowing Seat Type LH Side)

Hide 79236A 14.REMOVE NO. 2 SEAT LEG COVER (for Manual Stowing Seat Type LH Side)

Hide 79273 15.REMOVE NO. 2 SEAT HINGE COVER (for Manual Stowing Seat Type LH Side)

Hide 16.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Manual Stowing Seat Type LH Side)

Hide 72906 17.REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH (for Manual Stowing Seat Type LH Side)

Hide 67881A 18.REMOVE BACK DOOR WEATHERSTRIP

Hide 67935 19.REMOVE BACK DOOR SCUFF PLATE

Hide 58625D 20.REMOVE REAR FLOOR NO. 1 MAT PLATE (for Tumble Seat Type, Manual Stowing Seat Type)

Hide 58625D 21.REMOVE REAR FLOOR NO. 1 MAT PLATE (for Power Stowing Seat Type)

Hide 64735G 23.REMOVE DECK TRIM SIDE SERVICE HOLE COVER LH

Hide 64766 24.REMOVE QUARTER TRIM JACK COVER SUB-ASSEMBLY (for LH Side)

Hide 64740A 25.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Captain Seat Type)

Hide 64740A 26.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Except Captain Seat Type)

Hide 62639A 27.REMOVE QUARTER PILLAR GARNISH LH (for Captain Seat Type)

Hide 62639A 28.REMOVE QUARTER PILLAR GARNISH LH (for Except Captain Seat Type)

Hide 62472A 29.REMOVE INNER ROOF SIDE GARNISH LH

Hide 62452C 30.REMOVE REAR ROOF SIDE RAIL GARNISH LH

Hide 62720A 31.REMOVE QUARTER WINDOW ASSEMBLY

B140655E03
1.438,1.813 1.615,1.813 1.615,1.813 1.615,1.531 false 0.354,1.719 1.406,2.031 1.052,0.313 10 true Protective Tape

HINT:

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


NOTICE:

When separating the quarter window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.


a.

Disconnect the 2 connectors.


b.

Using a knife, cut off the moulding as shown in the illustration.

B140656E02
1.167,0.969 1.51,1.198 0.344,0.229 10 false Cut 1.49,0.604 1.833,0.76 0.344,0.156 10 false Cut 3.594,2.219 3.938,2.448 0.344,0.229 10 false Cut 5.865,0.802 6.208,1.031 0.344,0.229 10 false Cut

NOTICE:

Be careful not to damage the vehicle body.



c.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



d.

From the interior, insert a piano wire between the vehicle body and the quarter window glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


f.
B140658E02
1.781,1.302 1.781,1.729 false 1.333,1.729 2.635,2.125 1.302,0.396 10 true Piano Wire

Cut through the adhesive by pulling the piano wire around the quarter window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the quarter window glass.



g.

Using suction cups, remove the quarter window glass.


Hide 62720A 32.CLEAN QUARTER WINDOW ASSEMBLY

a.
BO04421

Clean the outer edges of the glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Ever if using new glass, clean the glass with a non-residue solvent.




Hide 64740A 33.CLEAN VEHICLE BODY

a.
B106081E50
0.406,1.375 0.406,0.24 false 2.198,1.49 2.198,0.24 false 0.896,1.5 0.979,1.677 false 2.073,1.771 1.854,1.823 false 0.125,0.052 0.823,0.25 0.698,0.198 10 false Adhesive 1.906,0.042 2.604,0.24 0.698,0.198 10 false Adhesive 0.917,1.688 1.76,1.917 0.844,0.229 10 false Vehicle Body

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.