Home › Vehicle Interior › SLIDING ROOF › SLIDING ROOF SYSTEM
RM24M0E _58 Vehicle Interior _059597 SLIDING ROOF _0292254 SLIDING ROOF SYSTEM C

SLIDING ROOF  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is output when the sliding roof drive gear (rear sunshade control ECU) detects that the sliding roof control switch is stuck for 30 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2342 Sliding roof drive gear (rear sunshade control ECU) detects sliding roof control switch is stuck for 30 seconds or more
·

Sliding roof drive gear (Rear sunshade control ECU)

·

Power slide door control switch (Front sliding roof control switch)

·

Wire harness



WIRING DIAGRAM

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF CONTROL SWITCH)
a.

Use the Data List to check if the sliding roof control switch is functioning properly.

Sliding roof drive gear (Rear sunshade control ECU):
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
Open Switch Failure (Current) SLIDE OPEN switch condition (current) / Fail or Not Fail Fail: SLIDE OPEN switch is stuck
Not Fail: SLIDE OPEN switch is not stuck
-
Open Switch Failure (Past) SLIDE OPEN switch condition (past) / Fail or Not Fail Fail: SLIDE OPEN switch was stuck in past
Not Fail: SLIDE OPEN switch was not stuck in past
-

OK:

"Not Fail" appears on tester screen.




OK

2.CHECK SLIDING ROOF FUNCTION

NG

4.INSPECT POWER SLIDE DOOR CONTROL SWITCH (FRONT SLIDING ROOF CONTROL SWITCH)
2.CHECK SLIDING ROOF FUNCTION
a.

Check the auto operation with the sliding roof control switch (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SYSTEM>OPERATION CHECK).

OK:

Auto operation operates normally with sliding roof control switch.




OK

3.DELETE DTC

NG

7.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (REAR SUNSHADE CONTROL ECU)
3.DELETE DTC

NEXT

END

4.INSPECT POWER SLIDE DOOR CONTROL SWITCH (FRONT SLIDING ROOF CONTROL SWITCH)
B135700E02
2.87,3.706 3.211,3.850 0.341,0.144 10 OPN 0.268,4.403 0.568,4.547 0.299,0.144 10 CLS 0.34,3.688 0.468,3.830 0.128,0.142 10 E 0.608,4.476 1.012,4.164 false 0.499,3.776 1.178,4.033 false 2.054,3.999 2.849,3.784 false

a.

Remove the map light.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Condition Specified Condition
3 (OPN) - 7 (E) Front sliding roof control switch is OPEN Below 1 Ω
8 (CLS) - 7 (E) Front sliding roof control switch is CLOSE Below 1 Ω
3 (OPN) - 7 (E)
8 (CLS) - 7 (E)
Front sliding roof control switch is OFF 10 kΩ or higher




NG

5.REPLACE MAP LIGHT ASSEMBLY (FRONT SLIDING ROOF CONTROL SWITCH)

OK

10.CHECK WIRE HARNESS (POWER SLIDE DOOR CONTROL SWITCH - SLIDING ROOF DRIVE GEAR AND BODY GROUND)
5.REPLACE MAP LIGHT ASSEMBLY (FRONT SLIDING ROOF CONTROL SWITCH)
a.

Temporarily replace the map light (front sliding roof control switch) with a new or normally functioning one.



NEXT

6.DELETE DTC
6.DELETE DTC

NEXT

END

7.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (REAR SUNSHADE CONTROL ECU)
a.

Check that the sliding roof drive gear can be initialized (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SYSTEM>INITIALIZATION).

OK:

Sliding roof drive gear can be initialized.




OK

8.CHECK SLIDING ROOF FUNCTION

NG

10.CHECK WIRE HARNESS (POWER SLIDE DOOR CONTROL SWITCH - SLIDING ROOF DRIVE GEAR AND BODY GROUND)
8.CHECK SLIDING ROOF FUNCTION
a.

Check the auto operation with the sliding roof control switch (see page Vehicle Interior>SLIDING ROOF>SLIDING ROOF SYSTEM>OPERATION CHECK).

OK:

Auto operation operates normally with sliding roof control switch.




OK

9.DELETE DTC

NG

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (REAR SUNSHADE CONTROL ECU)

9.DELETE DTC

NEXT

END

10.CHECK WIRE HARNESS (POWER SLIDE DOOR CONTROL SWITCH - SLIDING ROOF DRIVE GEAR AND BODY GROUND)
a.

Disconnect the Q16 switch connector.


b.

Disconnect the N2 gear connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
Q16-3 (OPN) - N2-7 (OPN) Below 1 Ω
Q16-8 (CLS) - N2-9 (CLS) Below 1 Ω
Q16-7 (E) - Body ground Below 1 Ω
Q16-3 (OPN) - Body ground 10 kΩ or higher
Q16-8 (CLS) - Body ground 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (REAR SUNSHADE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR