FREEZE FRAME DATA
Troubleshooting · Vehicles built Jul 2007 – Nov 2007
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
| DESCRIPTION |
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
These data sets can be used to simulate the conditions of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.
![]() ![]() |
- HINT:
- If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.
- 3 data sets before the DTC was set
- 1 data set when the DTC was set
- 1 data set after the DTC was set
| LIST OF FREEZE FRAME DATA |
| LABEL (Intelligent Tester Display) |
Measure Item |
Diagnostic Note |
| Injector (Port) |
Injection period of No. 1 cylinder |
- |
| IGN Advance |
Ignition timing advance for No. 1 cylinder |
- |
| Calculate Load |
Load calculated by ECM |
- |
| MAF |
Air flow rate from MAF meter |
If value approximately 0.0 g/sec:
|
| Engine Speed |
Engine speed |
- |
| Vehicle Speed |
Vehicle speed |
Speed indicated on speedometer |
| Coolant Temp |
Engine coolant temperature |
If value -40°C (-40°F), sensor circuit open If value 140°C (284°F) or more, sensor circuit shorted |
| Intake Air |
Intake air temperature |
If value -40°C (-40°F), sensor circuit open If value 140°C (284°F) or more, sensor circuit shorted |
| Air-Fuel Ratio |
Ratio compared to stoichiometric level |
- |
| Purge Density Learn Value |
Learning value of purge density |
- |
| Evap Purge Flow |
Ratio of evaporative purge flow to intake air volume |
- |
| EVAP (Purge) VSV |
EVAP (Purge) VSV control duty |
Order signal from ECM |
| Knock Correct Learn Value |
Correction learning value of knocking |
- |
| Knock Feedback Value |
Feedback value of knocking |
- |
| Accelerator Position No.1 |
Absolute Accelerator Pedal Position (APP) No. 1 |
- |
| Accelerator Position No.2 |
Absolute APP No. 2 |
- |
| Throttle Position |
Throttle position |
- |
| Throttle Sensor Position |
Throttle sensor positioning |
Recognition value for throttle opening angle on ECM Read value with ignition switch ON |
| Throttle Sensor Position #2 |
Throttle sensor positioning #2 |
Recognition value for throttle opening angle on ECM Read value with ignition switch ON |
| Throttle Motor |
Throttle motor |
- |
| O2S B1 S2 |
Heated oxygen sensor output voltage |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor |
| O2S B2 S2 |
Heated oxygen sensor output voltage |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor |
| AFS B1 S1 |
A/F sensor output voltage |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor |
| AFS B2 S1 |
A/F sensor output voltage |
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor |
| AFS B2 S1 |
A/F sensor output current |
- |
| Short FT #1 |
Short-term fuel trim (Bank 1) |
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 |
Long-term fuel trim (Bank 1) |
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve |
| Short FT #2 |
Short-term fuel trim (Bank 2) |
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #2 |
Long-term fuel trim (Bank 2) |
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve |
| Fuel System Status (Bank1) |
Fuel system status (Bank1) |
|
| Fuel System Status (Bank2) |
Fuel system status (Bank2) |
|
| AF FT B1 S1 |
Short-term fuel trim associated with bank 1 sensor 1 |
- |
| AFS B1 S1 |
A/F sensor output current |
- |
| AF FT B2 S1 |
Short-term fuel trim associated with bank 2 sensor 1 |
- |
| Initial Engine Coolant Temp |
Initial engine coolant temperature |
- |
| Initial Intake Air Temp |
Initial intake air temperature |
- |
| Injection Volum (Cylinder1) |
Injection volume (cylinder 1) |
Total fuel injection volume of 10 injections |
| Starter Signal |
Starter signal |
- |
| Power Steering Switch |
Power steering signal |
- |
| Power Steering Signal |
Power steering signal (history) |
This signal status usually ON until battery terminals disconnected |
| Closed Throttle Position SW |
Closed throttle position switch |
- |
| A/C Signal |
A/C signal |
- |
| Neutral Position SW Signal |
PNP switch status (for A/T models) |
- |
| Electrical Load Signal |
Electrical load signal |
- |
| Stop Light Switch |
Stop light switch |
- |
| Battery Voltage |
Battery voltage |
- |
| Atmosphere Pressure |
Atmospheric pressure |
- |
| Fuel Pump Speed Control |
Fuel pump speed control status |
- |
| ACIS VSV |
ACIS VSV status |
- |
| ACT VSV |
A/C cut status |
- |
| VVT Control Status (Bank2) |
VVT control status |
- |
| EVAP Purge VSV |
VSV status for EVAP control |
VSV for EVAP controlled by ECM (ground side duty control) |
| Fuel Pump/Speed Status |
Fuel pump status |
- |
| VVT Control Status (Bank1) |
VVT control status |
- |
| TC and TE1 |
TC and CG (TE1) terminal of DLC3 |
- |
| Engine Speed of Cyl #1 |
Engine speed for cylinder 1 |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| Engine Speed of Cyl #2 |
Engine speed for cylinder 2 |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| Engine Speed of Cyl #3 |
Engine speed for cylinder 3 |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| Engine Speed of Cyl #4 |
Engine speed for cylinder 4 |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| Engine Speed of Cyl #5 |
Engine speed for cylinder 5 |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| Engine Speed of Cyl #6 |
Engine speed for cylinder 6 |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| Av Engine Speed of All Cyl |
Engine speed for all cylinders |
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test |
| VVT Aim Angle (Bank1) |
VVT aim angle |
- |
| VVT Change Angle (Bank1) |
VVT change angle |
- |
| VVT OCV Duty (Bank1) |
VVT OCV operation duty |
- |
| VVT Aim Angle (Bank2) |
VVT aim angle |
- |
| VVT Change Angle (Bank2) |
VVT change angle |
- |
| VVT OCV Duty (Bank2) |
VVT OCV operation duty |
- |
| Idle Fuel Cut |
Idle fuel cut |
ON: when throttle valve fully closed and engine speed over 3,500 rpm |
| FC TAU |
Fuel cut TAU: Fuel cut during very light load |
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete |
| Engine Run Time |
Accumulated engine running time |
- |
| Time after DTC Cleared |
Cumulative time after DTC cleared |
- |
| Distance from DTC Cleared |
Accumulated distance from DTC cleared |
- |
| Warmup Cycle Cleard DTC |
Number of warm-up cycles after DTC cleared |
- |

