2011-2016 FJ Cruiser · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built Dec 2007 – Jul 2009

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


DESCRIPTION
Freeze frame data record the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air fuel ratio was LEAN or RICH, and other data, from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
These data sets can be used to simulate the conditions of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.
A103809E36

HINT:
If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.

  1. 3 data sets before the DTC was set
  2. 1 data set when the DTC was set
  3. 1 data set after the DTC was set

LIST OF FREEZE FRAME DATA
*: for Euro-OBD vehicle.
Intelligent Tester Display
Measure Item
Diagnostic Note
Injector (Port)
Injection period of No. 1 cylinder
-
IGN Advance
Ignition timing advance for No. 1 cylinder
-
Calculate Load
Load calculated by ECM
-
Vehicle Load*
Vehicle load
-
MAF
Air flow rate from MAF meter
If value approximately 0.0 g/sec:
  1. Mass air flow meter power source circuit open or short
  2. VG circuit open or short
    If value 160.0 g/sec or more:
  3. E2G circuit open
Engine Speed
Engine speed
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature
If value -40°C (-40°F), sensor circuit open
If value 140°C (284°F) or more, sensor circuit shorted
Intake Air
Intake air temperature
If value -40°C (-40°F), sensor circuit open
If value 140°C (284°F) or more, sensor circuit shorted
Air-Fuel Ratio
Ratio compared to stoichiometric level
-
Purge Density Learn Value
Learning value of purge density
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
EVAP (Purge) VSV
EVAP (Purge) VSV control duty
Order signal from ECM
Knock Correct Learn Value
Correction learning value of knocking
-
Knock Feedback Value
Feedback value of knocking
-
Accelerator Position No. 1
Absolute Accelerator Pedal Position (APP) No. 1
-
Accelerator Position No. 2
Absolute APP No. 2
-
Throttle Position
Throttle position
-
Throttle Sensor Position
Throttle sensor positioning
Recognition value for throttle opening angle on ECM
Read value with ignition switch ON
Throttle Sensor Position #2
Throttle sensor positioning #2
Recognition value for throttle opening angle on ECM
Read value with ignition switch ON
Throttle Motor
Throttle motor
-
O2S B1 S2
Heated oxygen sensor output voltage
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
O2S B2 S2
Heated oxygen sensor output voltage
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
AFS B1 S1
A/F sensor output voltage
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
AFS B2 S1
A/F sensor output voltage
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
AFS B2 S1
A/F sensor output current
-
Total FT #1*
Total fuel trim (bank 1)
-
Total FT #2*
Total fuel trim (bank 2)
-
Short FT #1
Short-term fuel trim (Bank 1)
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim (Bank 1)
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value
Short FT #2
Short-term fuel trim (Bank 2)
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #2
Long-term fuel trim (Bank 2)
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value
Fuel System Status (Bank1)
Fuel system status (Bank1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OL FAULT: Open loop due to detected system fault
  5. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
Fuel System Status (Bank2)
Fuel system status (Bank2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  3. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OL FAULT: Open loop due to detected system fault
  5. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control, malfunctioning
AF Lambda B1 S1
Short-term fuel trim associated with bank 1 sensor 1
-
AFS B1 S1
A/F sensor output current
-
AF FT B2 S1
Short-term fuel trim associated with bank 2 sensor 1
-
Catalyst Temp (B1 S1)*
Estimated catalyst temperature (bank 1 sensor 1)
-
Catalyst Temp (B2 S1)*
Estimated catalyst temperature (bank 2 sensor 1)
-
Catalyst Temp (B1 S2)*
Estimated catalyst temperature (bank 1 sensor 2)
-
Catalyst Temp (B2 S2)*
Estimated catalyst temperature (bank 2 sensor 2)
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Injection Volum (Cylinder1)
Injection volume (cylinder 1)
Total fuel injection volume of 10 injections
Starter Signal
Starter signal
-
Power Steering Switch
Power steering signal
-
Power Steering Signal
Power steering signal (history)
This signal status usually ON until battery terminals disconnected
Closed Throttle Position SW
Closed throttle position switch
-
A/C Signal
A/C signal
-
Neutral Position SW Signal
PNP switch status (for A/T models)
-
Electrical Load Signal
Electrical load signal
-
Stop Light Switch
Stop light switch
-
Battery Voltage
Battery voltage
-
Atmosphere Pressure
Atmospheric pressure
-
Fuel Pump Speed Control
Fuel pump speed control status
-
ACIS VSV
ACIS VSV status
-
ACT VSV
A/C cut status
-
VVT Control Status (Bank2)
VVT control status
-
EVAP Purge VSV
VSV status for EVAP control
VSV for EVAP controlled by ECM (ground side duty control)
Fuel Pump/Speed Status
Fuel pump status
-
VVT Control Status (Bank1)
VVT control status
-
TC and TE1
TC and CG (TE1) terminal of DLC3
-
Engine Speed of Cyl #1
Engine speed for cylinder 1
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
Engine Speed of Cyl #2
Engine speed for cylinder 2
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
Engine Speed of Cyl #3
Engine speed for cylinder 3
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
Engine Speed of Cyl #4
Engine speed for cylinder 4
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
Engine Speed of Cyl #5
Engine speed for cylinder 5
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
Engine Speed of Cyl #6
Engine speed for cylinder 6
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
Av Engine Speed of All Cyl
Engine speed for all cylinders
Output only when [Check the Cylinder Compression] performed using Active Test 51199 rpm: Not performed Active Test
VVT Aim Angle (Bank1)
VVT aim angle
-
VVT Change Angle (Bank1)
VVT change angle
-
VVT OCV Duty (Bank1)
VVT OCV operation duty
-
VVT Aim Angle (Bank2)
VVT aim angle
-
VVT Change Angle (Bank2)
VVT change angle
-
VVT OCV Duty (Bank2)
VVT OCV operation duty
-
Idle Fuel Cut
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 3500 rpm
FC TAU
Fuel cut TAU: Fuel cut during very light load
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Ignition*
Ignition counter
-
Cylinder #1 Misfire Count*
Cylinder #1 misfire
Only displayed during idling
Cylinder #2 Misfire Count*
Cylinder #2 misfire
Only displayed during idling
Cylinder #3 Misfire Count*
Cylinder #3 misfire
Only displayed during idling
Cylinder #4 Misfire Count*
Cylinder #4 misfire
Only displayed during idling
Cylinder #5 Misfire Count*
Cylinder #5 misfire
Only displayed during idling
Cylinder #6 Misfire Count*
Cylinder #6 misfire
Only displayed during idling
All Cylinders Misfire Count*
All cylinders misfire
Only displayed during idling
Misfire RPM*
Engine speed when misfire occurred
-
Misfire Load*
Engine load when misfire occurred
-
Misfire Margin*
Margin to detect engine misfire
-
Engine Run Time
Accumulated engine running time
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Number of warm-up cycles after DTC cleared
-
← FREEZE FRAME DATA (Jul 2007 – Nov 2007)FREEZE FRAME DATA (Aug 2009 – Oct 2010) →