2011-2016 FJ Cruiser · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


DESCRIPTION
Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
A103809E36

HINT:
If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.

  1. 3 data sets before the DTC was stored.
  2. 1 data set when the DTC was stored.
  3. 1 data set after the DTC was stored.

PENDING FREEZE FRAME DATA

HINT:
Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / DTC.

  5. Select a DTC in order to display its pending freeze frame data.

    HINT:
    1. Pending freeze frame data is cleared when any of the following occurs.
      1. Using the intelligent tester, the DTCs are cleared.
      2. The cable is disconnected from the negative (- ) battery terminal.
      3. 40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)
    2. With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new one of the newly detected DTC in the next trip.

    A251781E12
    A251782E14


LIST OF FREEZE FRAME DATA
*1: for Automatic Transmission
*2: w/ Secondary Air Injection System
*3: w/o Secondary Air Injection System
*4: for Manual Transmission
Display Item
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If the mass air flow volume is approximately 0.0 gm/sec.:
  1. The mass air flow meter power source circuit is open or short.
  1. The VG circuit is open or short.
If the mass air flow volume is 271.0 gm/sec. or more:
  1. The E2G circuit is open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is 140°C (284°F): the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is 140°C (284°F): the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Glow Indicator Supported*1
Status of glow indicator supported
-
Glow Indicator*1
Glow Indicator
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No.2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle sensor positioning
-
Throttl Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Position
Throttle position
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
ISC Flow
Flow rate calculated using information from each sensor
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
ISC Position
Requested opening amount calculated using ISC control
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
ISC Feedback Value
ISC feedback compensation amount
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
ISC Learning Value
ISC learned compensation amount
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Electric Load Feedback Val
Compensation flow rate according to electrical load
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
PS Feedback Val
Compensation flow rate according to power steering load
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Low Revolution Control
Low engine speed control operation state
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Neutral Control
N position control status for automatic transmission
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
N Range Status*1
Shift lever N status
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Eng Stall Control FB Flow
Intake air compensation flow rate
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Deposit Loss Flow
Flow loss due to deposits
  1. This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
  2. Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
  3. When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the fuses (EFI and ETCS fuses), perform the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
    1. Start the engine cold and allow the engine to idle.
    2. After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
    3. Turn the ignition switch off and wait for 30 seconds.
    4. Start the engine again, and allow the engine to idle for 5 minutes.
Fuel Pump Duty*2
Fuel pump duty
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status*3
Fuel pump/speed status
-
Current Fuel Type
Current fuel type status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
EVAP Purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AF Lambda B2S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
Air fuel ratio sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Voltage B2S1
Air fuel ratio sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
Air fuel ratio sensor current
-
AFS Current B2S1
Air fuel ratio sensor current
-
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio (for Bank 1)
-
A/F Heater Duty #2
Air fuel ratio sensor heater duty ratio (for Bank 2)
-
O2S B1S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B2S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S Impedance B1S2
Heated oxygen sensor impedance (for Sensor 2)
-
O2S Impedance B2S2
Heated oxygen sensor impedance (for Sensor 2)
-
O2 Heater B1S2
Heated oxygen sensor heater
-
O2 Heater B2S2
Heated oxygen sensor heater
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
O2 Heater Curr Val B2S2
Heated oxygen sensor current
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
A/F Learn Value Idle #1
Air fuel ratio learn value area of idle (for Bank 1)
-
A/F Learn Value Low #1
Air fuel ratio learn value area of low load (for Bank 1)
-
A/F Learn Value Mid1 #1
Air fuel ratio learn value area of middle load 1 (for Bank 1)
-
A/F Learn Value Mid2 #1
Air fuel ratio learn value area of middle load 2 (for Bank 1)
-
A/F Learn Value High #1
Air fuel ratio learn value area of high load (for Bank 1)
-
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
A/F Learn Value Idle #2
Air fuel ratio learn value area of idle (for Bank 2)
-
A/F Learn Value Low #2
Air fuel ratio learn value area of low load (for Bank 2)
-
A/F Learn Value Mid1 #2
Air fuel ratio learn value area of middle load 1 (for Bank 2)
-
A/F Learn Value Mid2 #2
Air fuel ratio learn value area of middle load 2 (for Bank 2)
-
A/F Learn Value High #2
Air fuel ratio learn value area of high load (for Bank 2)
-
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (for Bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (for Bank 2)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Air Pump Pressure (Absolute)*2
Air pump pressure (for Bank 1)
-
Air Pump2 Pressure (Absolute)*2
Air pump pressure (for Bank 2)
-
Air Pump Pulsation Pressure*2
Air pump pulsation pressure
-
Secondary Air Control VSV*2
Secondary air control VSV status
-
2nd Air System Status*2
Secondary air injection system status
-
Al Test*2
Secondary air injection system operation prohibition
-
Subfreezing Conditions*2
Subfreezing conditions status
-
Air Pump Freeze*2
Air pump freeze status
-
Air Switching Valve Freeze*2
Air switching valve freeze status
-
Air Switching Valve2 Freeze*2
Air switching valve2 freeze status
-
Air Pump Heater*2
Air pump heater status
-
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Actual VVT Angle #1
Actual VVT angle (for Bank 1)
-
Actual VVT Angle #2
Actual VVT angle (for Bank 2)
-
Actual VVT Ex Angle #1
Actual exhaust VVT angle (for Bank 1)
-
Actual VVT Ex Angle #2
Actual exhaust VVT angle (for Bank 2)
-
VVT Control Status #1
VVT control status
-
VVT Control Status #2
VVT control status
-
VVT Advance Fail
VVT control failure status
-
Catalyst Temp B1S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B2S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B1S2
Estimated catalyst temperature (for Sensor 2)
-
Catalyst Temp B2S2
Estimated catalyst temperature (for Sensor 2)
-
Starter Signal
Starter switch (STSW) signal
-
Power Steering Signal
Power steering switch status
-
Neutral Position SW Signal*1
Park/neutral position (PNP) switch signal
-
Clutch Switch*4
Clutch Switch
-
Transfer Neutral*1
Transfer neutral status
-
4WD SW
4WD switch status
-
Transfer L4
Transfer L4 switch status
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Accumulated distance from battery cable disconnected
-
IG OFF Elapsed Time*2
Time after ignition switch off
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C*2
Catalyst over temperature misfire prevention F/C not available
-
Cat OT MF F/C History*2
Catalyst over temperature misfire prevention F/C history OFF
-
Cat OT MF F/C Cylinder#1*2
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2*2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3*2
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4*2
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#5*2
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#6*2
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Engine Speed (Starter Off)
Engine speed when starter off
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Starter Count
Number of times starter turned on after ignition switch turned to ON
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Run Dist of Previous Trip
Distance driven during previous trip
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:
Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.
Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Previous Trip Intake Temp
Intake air temperature during previous trip
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Engine Oil Temperature
Engine oil temperature (estimated temperature)
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Ambient Temp for A/C
Ambient temperature
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Previous Trip Ambient Temp
Ambient temperature during previous trip
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Engine Start Hesitation
History of hesitation during engine start
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Low Rev for Eng Start
History of low engine speed after engine start
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Minimum Engine Speed
Minimum engine speed
Reference:
Check the value when engine stalls, is difficult to start, or idles roughly.
Power Steering Pressure
Power steering pressure switch (sensor)
-
ACT VSV
A/C cut status for Active Test
-
Brake Override System
Brake override system status
-
Idle Fuel Cut
Fuel cut idle
ON: when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU
Fuel cut during very light load
Fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut
-
Immobiliser Fuel Cut History
Immobiliser fuel cut history
-
Electrical Load Signal 1
Electrical load signal
-
Electrical Load Signal 2
Electrical load signal
-
A/F Sensor Determination (worst value) #1*2
Worst judgment value of air fuel ratio sensor output (for Bank 1)
-
A/F Sensor Determination (worst value) #2*2
Worst judgment value of air fuel ratio sensor output (for Bank 2)
-
Engine Speed Fluctuation Avg (worst value) #1*2
Worst value of average engine speed fluctuation (Cylinder 1)
-
Engine Speed Fluctuation Avg (worst value) #2*2
Worst value of average engine speed fluctuation (Cylinder 2)
-
Engine Speed Fluctuation Avg (worst value) #3*2
Worst value of average engine speed fluctuation (Cylinder 3)
-
Engine Speed Fluctuation Avg (worst value) #4*2
Worst value of average engine speed fluctuation (Cylinder 4)
-
Engine Speed Fluctuation Avg (worst value) #5*2
Worst value of average engine speed fluctuation (Cylinder 5)
-
Engine Speed Fluctuation Avg (worst value) #6*2
Worst value of average engine speed fluctuation (Cylinder 6)
-
SPD (NT)*1
Input shaft speed
Data is displayed in increments of 50 rpm.
SPD (SP2)*1
Output shaft speed
-
← FREEZE FRAME DATA (Aug 2012 – Jul 2014)CHECK MODE PROCEDURE (from Jul 2007) →