2011-2016 FJ Cruiser · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


DESCRIPTION
Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
A103809E36

HINT:
If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.

  1. 3 data sets before the DTC was stored.
  2. 1 data set when the DTC was stored.
  3. 1 data set after the DTC was stored.

LIST OF FREEZE FRAME DATA
*1: for Automatic Transmission models
*2: for Manual Transmission models
Display Item
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If the mass air flow volume is approximately 0.0 g/sec.:
  1. The mass air flow meter power source circuit is open or short.
  1. The VG circuit is open or short.
If the mass air flow volume is 271.0 g/sec. or more:
  1. The E2G circuit is open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is 140°C (284°F): the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C (-40°F): the sensor circuit is open.
If the value is 140°C (284°F): the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No.2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle sensor positioning
-
Throttl Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Position
Throttle position
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control
For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value
ISC feedback compensation amount
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Compensation flow rate according to power steering load
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state
For use when engine stall, starting problems or rough idle is present.
N Range Status*1
Shift lever N status
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate
For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow
Flow loss due to deposits
For use when engine stall, starting problems or rough idle is present.
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
EVAP Purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at A/F sensor
-
AF Lambda B2S1
Fuel trim at A/F sensor
-
AFS Voltage B1S1
AFS Voltage B2S1
A/F sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
A/F sensor current
-
AFS Current B2S1
A/F sensor current
-
A/F Heater Duty #1
A/F heater duty ratio (for Bank 1)
-
A/F Heater Duty #2
A/F heater duty ratio (for Bank 2)
-
O2S B1S2
O2S B2S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2 Heater B1S2
Heated oxygen sensor heater
-
O2 Heater B2S2
Heated oxygen sensor heater
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
O2 Heater Curr Val B2S2
Heated oxygen sensor current
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (for Bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (for Bank 2)
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)
For use when engine stall, starting problems or rough idle is present.
VVT Control Status #1
VVT control status
-
VVT Control Status #2
VVT control status
-
VVT Advance Fail
VVT control failure status
-
Catalyst Temp B1S1
Catalyst Temp B2S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B1S2
Catalyst Temp B2S2
Estimated catalyst temperature (for Sensor 2)
-
Starter Signal
Starter switch (STSW) signal
-
Power Steering Signal
Power steering switch status
-
Neutral Position SW Signal*1
Park/Neutral position (PNP) switch signal
-
Clutch Switch*2
Clutch Switch
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Accumulated distance from battery cable disconnected
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Engine Speed (Starter Off)
Engine speed when starter off
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start
For use when engine stall, starting problems or rough idle is present.
Low Rev for Eng Start
History of low engine speed after engine start
For use when engine stall, starting problems or rough idle is present.
Minimum Engine Speed
Minimum engine speed
For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure
Power steering pressure switch (sensor)
-
ACT VSV
A/C cut status for Active Test
-
Idle Fuel Cut Prohibit
Prohibition of fuel cut at idle
-
Idle Fuel Cut
Fuel cut idle
ON: when the throttle valve is fully closed and the engine speed is more than 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut
-
Electrical Load Signal 1
Electrical load signal
-
Electrical Load Signal 2
Electrical load signal
-
SPD (NT)*1
Input shaft speed
Data is displayed in increments of 50 rpm.
SPD (SP2)*1
Output shaft speed
-
← FREEZE FRAME DATA (Dec 2007 – Jul 2009)FREEZE FRAME DATA (Nov 2010 – Jul 2011) →