FREEZE FRAME DATA
Troubleshooting · Vehicles built Nov 2010 – Jul 2011
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
| DESCRIPTION |
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
![]() ![]() |
- HINT:
- If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.
- 3 data sets before the DTC was stored.
- 1 data set when the DTC was stored.
- 1 data set after the DTC was stored.
| LIST OF FREEZE FRAME DATA |
*2: for Manual Transmission Models
| Display Item |
Measurement Item |
Diagnostic Note |
| Vehicle Speed |
Vehicle speed |
Speed indicated on speedometer. |
| Engine Speed |
Engine speed |
- |
| Calculate Load |
Calculated load |
Calculated load by ECM. |
| Vehicle Load |
Vehicle load |
- |
| MAF |
Mass air flow volume |
If the mass air flow volume is approximately 0.0 gm/sec.:
|
| Atmosphere Pressure |
Atmosphere pressure |
- |
| Coolant Temp |
Engine coolant temperature |
If the value is -40°C (-40°F): the sensor circuit is open. If the value is 140°C (284°F): the sensor circuit is shorted. |
| Intake Air |
Intake air temperature |
If the value is -40°C (-40°F): the sensor circuit is open. If the value is 140°C (284°F): the sensor circuit is shorted. |
| Engine Run Time |
Accumulated engine running time |
- |
| Initial Engine Coolant Temp |
Engine coolant temperature at engine start |
- |
| Initial Intake Air Temp |
Intake air temperature at engine start |
- |
| Battery Voltage |
Battery voltage |
- |
| Accel Sens. No.1 Volt % |
Absolute Accelerator Pedal Position (APP) No. 1 |
- |
| Accel Sens. No.2 Volt % |
Absolute APP No. 2 |
- |
| Throttle Sensor Volt % |
Throttle sensor positioning |
- |
| Throttl Sensor #2 Volt % |
Throttle sensor positioning #2 |
- |
| Throttle Sensor Position |
Throttle sensor positioning |
- |
| Throttle Motor DUTY |
Throttle actuator |
- |
| Throttle Position |
Throttle position |
For use when engine stall, starting problems or rough idle is present. |
| ISC Flow |
Flow rate calculated using information from each sensor |
For use when engine stall, starting problems or rough idle is present. |
| ISC Position |
Requested opening amount calculated using ISC control |
For use when engine stall, starting problems or rough idle is present. |
| ISC Feedback Value |
ISC feedback compensation amount |
For use when engine stall, starting problems or rough idle is present. |
| ISC Learning Value |
ISC learned compensation amount |
For use when engine stall, starting problems or rough idle is present. |
| Electric Load Feedback Val |
Compensation flow rate according to electrical load |
For use when engine stall, starting problems or rough idle is present. |
| Air Conditioner FB Val |
Compensation flow rate according to air conditioner load |
For use when engine stall, starting problems or rough idle is present. |
| PS Feedback Val |
Compensation flow rate according to power steering load |
For use when engine stall, starting problems or rough idle is present. |
| Low Revolution Control |
Low engine speed control operation state |
For use when engine stall, starting problems or rough idle is present. |
| Neutral Control |
N position control status for automatic transmission |
For use when engine stall, starting problems or rough idle is present. |
| N Range Status*1 |
Shift lever N status |
For use when engine stall, starting problems or rough idle is present. |
| Eng Stall Control FB Flow |
Intake air compensation flow rate |
For use when engine stall, starting problems or rough idle is present. |
| Deposit Loss Flow |
Flow loss due to deposits |
For use when engine stall, starting problems or rough idle is present. |
| Injector (Port) |
Injection period of No. 1 cylinder |
- |
| Injection Volum (Cylinder 1) |
Injection volume |
- |
| Fuel Pump/Speed Status |
Fuel pump/speed status |
- |
| Current Fuel Type |
Current fuel type status |
- |
| EVAP (Purge) VSV |
EVAP purge VSV duty ratio |
- |
| Evap Purge Flow |
Ratio of evaporative purge flow to intake air volume |
- |
| Purge Density Learn Value |
Learning value of purge density |
- |
| EVAP Purge VSV |
EVAP Purge VSV |
- |
| Purge Cut VSV Duty |
Purge cut VSV duty |
- |
| Target Air-Fuel Ratio |
Ratio compared to stoichiometric level |
- |
| AF Lambda B1S1 |
Fuel trim at A/F sensor |
- |
| AF Lambda B2S1 |
Fuel trim at A/F sensor |
- |
| AFS Voltage B1S1 AFS Voltage B2S1 |
A/F sensor output |
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| AFS Current B1S1 |
A/F sensor current |
- |
| AFS Current B2S1 |
A/F sensor current |
- |
| A/F Heater Duty #1 |
A/F heater duty ratio (for Bank 1) |
- |
| A/F Heater Duty #2 |
A/F heater duty ratio (for Bank 2) |
- |
| O2S B1S2 O2S B2S2 |
Heated oxygen sensor output |
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| O2S Impedance B1S2 |
Sub heated oxygen sensor impedance (for Sensor 2) |
- |
| O2S Impedance B2S2 |
Sub heated oxygen sensor impedance (for Sensor 2) |
- |
| O2 Heater B1S2 |
Heated oxygen sensor heater |
- |
| O2 Heater B2S2 |
Heated oxygen sensor heater |
- |
| O2 Heater Curr Val B1S2 |
Heated oxygen sensor current |
- |
| O2 Heater Curr Val B2S2 |
Heated oxygen sensor current |
- |
| Short FT #1 |
Short-term fuel trim |
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #1 |
Long-term fuel trim |
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value. |
| Total FT #1 |
Total fuel trim |
- |
| Short FT #2 |
Short-term fuel trim |
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #2 |
Long-term fuel trim |
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value. |
| Total FT #2 |
Total fuel trim |
- |
| Fuel System Status #1 |
Fuel system status (for Bank 1) |
|
| Fuel System Status #2 |
Fuel system status (for Bank 2) |
|
| IGN Advance |
Ignition advance |
- |
| Knock Feedback Value |
Feedback value of knocking |
- |
| Knock Correct Learn Value |
Correction learning value of knocking |
- |
| Idle Spark Advn Ctrl #1 |
Individual cylinder timing advance compensation amount (No. 1) |
For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #2 |
Individual cylinder timing advance compensation amount (No. 2) |
For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #3 |
Individual cylinder timing advance compensation amount (No. 3) |
For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #4 |
Individual cylinder timing advance compensation amount (No. 4) |
For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #5 |
Individual cylinder timing advance compensation amount (No. 5) |
For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #6 |
Individual cylinder timing advance compensation amount (No. 6) |
For use when engine stall, starting problems or rough idle is present. |
| Actual VVT Angle #1 |
Actual VVT angle (for Bank 1) |
- |
| Actual VVT Angle #2 |
Actual VVT angle (for Bank 2) |
- |
| Actual VVT Ex Angle #1 |
Actual exhaust VVT angle (for Bank 1) |
- |
| Actual VVT Ex Angle #2 |
Actual exhaust VVT angle (for Bank 2) |
- |
| VVT Control Status #1 |
VVT control status |
- |
| VVT Control Status #2 |
VVT control status |
- |
| VVT Advance Fail |
VVT control failure status |
- |
| Catalyst Temp B1S1 Catalyst Temp B2S1 |
Estimated catalyst temperature (for Sensor 1) |
- |
| Catalyst Temp B1S2 Catalyst Temp B2S2 |
Estimated catalyst temperature (for Sensor 2) |
- |
| Starter Signal |
Starter switch (STSW) signal |
- |
| Power Steering Signal |
Power steering switch status |
- |
| Neutral Position SW Signal*1 |
Park/Neutral position (PNP) switch signal |
- |
| Clutch Switch*2 |
Clutch Switch |
- |
| Stop Light Switch |
Stop light switch |
- |
| A/C Signal |
A/C signal |
- |
| Closed Throttle Position SW |
Closed throttle position switch |
- |
| Fuel Cut Condition |
Fuel cut condition |
- |
| Immobiliser Communication |
Immobiliser communication |
- |
| TC Terminal |
TC terminal status |
- |
| Time after DTC Cleared |
Cumulative time after DTC cleared |
- |
| Distance from DTC Cleared |
Accumulated distance from DTC cleared |
- |
| Warmup Cycle Cleared DTC |
Warm-up cycle after DTC cleared |
- |
| Dist Batt Cable Disconnect |
Accumulated distance from battery cable disconnected |
- |
| TC and TE1 |
TC and CG (TE1) terminals of DLC3 |
- |
| Ignition Trig. Count |
Ignition counter |
- |
| Cylinder #1 Misfire Count |
Cylinder #1 misfire count |
- |
| Cylinder #2 Misfire Count |
Cylinder #2 misfire count |
- |
| Cylinder #3 Misfire Count |
Cylinder #3 misfire count |
- |
| Cylinder #4 Misfire Count |
Cylinder #4 misfire count |
- |
| Cylinder #5 Misfire Count |
Cylinder #5 misfire count |
- |
| Cylinder #6 Misfire Count |
Cylinder #6 misfire count |
- |
| All Cylinders Misfire Count |
All cylinders misfire count |
- |
| Misfire RPM |
Engine speed when misfire occurred |
- |
| Misfire Load |
Engine load when misfire occurred |
- |
| Misfire Margin |
Margin to detect engine misfire |
- |
| Engine Speed (Starter Off) |
Engine speed when starter off |
For use when engine stall, starting problems or rough idle is present. |
| Starter Count |
Number of times starter turned on after ignition switch turned to ON |
For use when engine stall, starting problems or rough idle is present. |
| Run Dist of Previous Trip |
Distance driven during previous trip |
For use when engine stall, starting problems or rough idle is present. |
| Engine Starting Time |
Time elapsed after engine started (interval between ignition switch ON and off) |
For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Coolant Temp |
Engine coolant temperature during previous trip |
For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Intake Temp |
Intake air temperature during previous trip |
For use when engine stall, starting problems or rough idle is present. |
| Engine Oil Temperature |
Engine oil temperature (estimated temperature) |
For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Eng Oil Temp |
Engine oil temperature during previous trip |
For use when engine stall, starting problems or rough idle is present. |
| Ambient Temp for A/C |
Ambient temperature |
For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Ambient Temp |
Ambient temperature during previous trip |
For use when engine stall, starting problems or rough idle is present. |
| Engine Start Hesitation |
History of hesitation during engine start |
For use when engine stall, starting problems or rough idle is present. |
| Low Rev for Eng Start |
History of low engine speed after engine start |
For use when engine stall, starting problems or rough idle is present. |
| Minimum Engine Speed |
Minimum engine speed |
For use when engine stall, starting problems or rough idle is present. |
| A/F Learn Value Idle #1 |
Air fuel ratio learn value area of idle (for Bank 1) |
- |
| A/F Learn Value Low #1 |
Air fuel ratio learn value area of low load (for Bank 1) |
- |
| A/F Learn Value Mid1 #1 |
Air fuel ratio learn value area of middle load 1 (for Bank 1) |
- |
| A/F Learn Value Mid2 #1 |
Air fuel ratio learn value area of middle load 2 (for Bank 1) |
- |
| A/F Learn Value High #1 |
Air fuel ratio learn value area of high load (for Bank 1) |
- |
| A/F Learn Value Idle #2 |
Air fuel ratio learn value area of idle (for Bank 2) |
- |
| A/F Learn Value Low #2 |
Air fuel ratio learn value area of low load (for Bank 2) |
- |
| A/F Learn Value Mid1 #2 |
Air fuel ratio learn value area of middle load 1 (for Bank 2) |
- |
| A/F Learn Value Mid2 #2 |
Air fuel ratio learn value area of middle load 2 (for Bank 2) |
- |
| A/F Learn Value High #2 |
Air fuel ratio learn value area of high load (for Bank 2) |
- |
| Power Steering Pressure |
Power steering pressure switch (sensor) |
- |
| ACT VSV |
A/C cut status for Active Test |
- |
| Idle Fuel Cut |
Fuel cut idle |
ON: when the throttle valve is fully closed and the engine speed is more than 3500 rpm. |
| FC TAU |
Fuel cut during very light load |
Fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete. |
| Immobiliser Fuel Cut |
Status of the immobiliser fuel cut |
- |
| Immobiliser Fuel Cut History |
Immobiliser fuel cut history |
- |
| Electrical Load Signal 1 |
Electrical load signal |
- |
| Electrical Load Signal 2 |
Electrical load signal |
- |
| SPD (NT)*1 |
Input shaft speed |
Data is displayed in increments of 50 rpm. |
| SPD (SP2)*1 |
Output shaft speed |
- |

