2011-2016 FJ Cruiser · Service Manual ENGINE

P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Diagnostic trouble codes · Vehicles built from Nov 2010

Also covers:

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear assembly ; and 2) changing the relative positions of the camshaft and crankshaft.
DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviation in crankshaft position sensor signal and VVT sensor (for intake side of bank 1) signal
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 1)
  3. Camshaft timing gear assembly (for bank 1)
  4. ECM
P0017
Deviation in crankshaft position sensor signal and VVT sensor (for exhaust side of bank 1) signal
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side of bank 1)
  3. Camshaft timing exhaust gear assembly (bank 1)
  4. ECM
P0018
Deviation in crankshaft position sensor signal and VVT sensor (for intake side of bank 2) signal
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 2)
  3. Camshaft timing gear assembly (for bank 2)
  4. ECM
P0019
Deviation in crankshaft position sensor signal and VVT sensor (for exhaust side of bank 2) signal
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side of bank 2)
  3. Camshaft timing exhaust gear assembly (for bank 2)
  4. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (Bank 1) or P0018 (Bank 2).
To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0017 (Bank 1) or P0019 (Bank 2).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0016, P0017, P0018 or P0019 is output
    A
    P0016, P0017, P0018 or P0019 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0016, P0017, P0018 or P0019 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Varies.



NG
Go to step 4
OK


3. ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 6
4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing oil control valve assembly.

    1. For intake side (Click here).
    2. For exhaust side (Click here).
    Result 
    Result
    Proceed to
    OK
    A
    NG
    (for intake camshaft)
    B
    NG
    (for exhaust camshaft)
    C



B
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) (Click here)

C
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) (Click here)
A


5. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing gear assembly (Click here).
  2. Inspect the camshaft timing exhaust gear assembly (Click here).
    Result 
    Result
    Proceed to
    OK
    A
    NG
    (Camshaft Timing Gear Assembly)
    B
    NG
    (Camshaft Timing Exhaust Gear Assembly)
    C


B
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)

C
REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (Click here)
A


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTC (Click here).

  1. Start the engine and warm it up.

  1. With the engine warmed up, idle it for 5 minutes. Then drive the vehicle for 10 minutes.

  1. Read the output pending DTCs using the tester.

    OK:
    No pending DTC is output.



NG
REPLACE ECM
OK

END


← P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (+ P0017, P0018, P0019) (Aug 2009 – Oct 2010)P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032, P0051, P0052) (Jul 2007 – Nov 2007) →