2011-2016 FJ Cruiser · Service Manual ENGINE

P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

Refer to DTC P0335 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0016
Deviations in crankshaft and camshaft position sensor 1 signals (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. Oil Control Valve (OCV)
  3. OCV filter
  4. Camshaft timing gear assembly
  5. ECM
P0018
Deviations in crankshaft and camshaft position sensor 2 signals (2 trip detection logic)

MONITOR DESCRIPTION

The ECM optimizes the valve timing by using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Oil Control Valve (OCV) and the VVT controller.
The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft. The ECM calibrates the intake valve timing by setting the intake camshaft to the most retarded angle while the engine is idling. The ECM closes the OCV to retard the cam. The ECM stores this value as the VVT learning value. When the difference between the target and actual intake valve timings is 5°CA (Crankshaft Angle) or less, the ECM stores it.
If the VVT learning value matches the following conditions, the ECM determines the existence of a malfunction in the VVT system, and sets a DTC.
  1. VVT learning value: Less than 22.5°CA, or more than 45.2°CA.
  2. Above condition continues for 18 seconds or more.
This DTC indicates that the intake camshaft has been installed toward the crankshaft at an incorrect angle, caused by factors such as the timing chain having jumped a tooth.
This monitor begins to run after the engine has idled for 5 minutes.

WIRING DIAGRAM

Refer to DTC P0010 (Click here).
Refer to DTC P0335 (Click here).
Refer to DTC P0340 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0016 or P0018
    A
    P0016 or P0018 and other DTCs
    B

    HINT:
    If any DTCs other than P0016 or P0018 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. CHECK VALVE TIMING (CHECK FOR LOOSE AND A JUMPED TOOTH OF TIMING CHAIN)

  1. G036290E05
    Remove the cylinder head cover (Click here or Click here).

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover (Click here or Click here).



NG
ADJUST VALVE TIMING (REPAIR OR REPLACE TIMING CHAIN) (Click here)
OK


3. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
A097066E06
  1. Remove the OCV.

  1. Measure the resistance between the terminals of the OCV.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    6.9 to 7.9 Ω at 20°C (68°F)

  1. Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


4. INSPECT OIL CONTROL VALVE FILTER

OK:
Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


5. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Confirm that no DTC is set using the tester.

    Result:
    Display (DTC Output)
    Proceed To
    P0016 or P0018
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)


← P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) (+ P0015, P0024, P0025) (from Aug 2014)P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (+ P0017, P0018, P0019) (Aug 2009 – Oct 2010) →