2011-2016 FJ Cruiser · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014


PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is output, perform troubleshooting procedures for that DTC.

  1. Check if sparks occur.

    1. Remove the intake air surge tank (Click here).

    2. Remove the 6 spark plugs (Click here).

    3. A227073
      Disconnect the 6 injector connectors.

    4. Install the spark plug to the ignition coil and connect the ignition coil connector.

    5. Remove the No. 2 engine room relay block cover.

    6. A227072E01
      Remove the circuit opening relay (C/OPN) from the No. 2 engine room relay block.
      Text in Illustration 
      *1
      No. 2 Engine Room Relay Block
      *2
      Circuit Opening Relay (C/OPN)

    7. A227074
      Ground the spark plug.

    8. Visually check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Install and test each spark plug and ignition coil individually, disconnecting the ignition coil and removing the spark plug when each test is complete.
      2. Be sure to ground the spark plug when checking.
      3. Replace the ignition coil if it receives an impact.
      4. Do not crank the engine for more than 2 seconds.

      If spark does not occur, perform the following procedure.

  1. Check that the wire harness side connector of the ignition coil is securely connected.

    Result 
    Result
    Proceed to
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test on each ignition coil.

    1. If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.

    2. Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.

      Result 
      Result
      Proceed to
      OK
      Replace ignition coil
      NG
      Go to next step

  1. Inspect the spark plug.

    1. Replace the spark plug with a normal one.

    2. Perform spark test again.

      Result 
      Result
      Proceed to
      OK
      Replace spark plug
      NG
      Go to next step


    1. A207834E02
      Check that power is supplied to the ignition coil.
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Ignition Coil)
      1. Turn the ignition switch to ON.
      2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      1 (+B) - 4 (GND)
      Ignition switch ON
      11 V to 14 V

      Result 
      Result
      Proceed to
      NG
      Check wiring between ignition switch and ignition coil and check ground circuit
      OK
      Replace the ECM (Click here)

  1. Install the 6 spark plugs (Click here).

  1. Install the intake air surge tank (Click here).

  1. Install the circuit opening relay (C/OPN) to the No. 2 engine room relay block.

  1. Install the No. 2 engine room relay block cover.

  1. Clear the DTC (Click here).

  1. Check for DTCs (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

  1. I039522E32
    Check the electrode.
    Text in Illustration 
    *a
    Ground

    1. Measure the resistance according to the value(s) in the table below.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark Plug (terminal part) - Body Ground
      Always
      10 MΩ or higher

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      2. If a megohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plug.

    3. A126881
      Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage on its threads and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Product
    DENSO made
    SK20HR11 or SK16HR11

    NOTICE:
    When replacing a spark plug, replace it with the same type of spark plug that is installed on the vehicle.

  1. B062019E01
    Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry with compressed air.

    Air Pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

  1. A227070E01
    Check the spark plug electrode gap.
    Text in Illustration 
    *a
    Spark Plug Electrode Gap

    Maximum electrode gap for used spark plug:
    1.3 mm (0.0512 in.)

    If the gap is more than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

← ON-VEHICLE INSPECTION (Aug 2009 – Jul 2014)COMPONENTS (Aug 2009 – Jul 2014) →