2011-2016 FJ Cruiser · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet.
The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
  1. No CKP sensor signal to ECM while cranking (1 trip detection logic)
  1. No CKP sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  1. Missing CKP sensor signal despite VVT sensor input normal after engine cranked.
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. Sensor plate (crankshaft)
  4. ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic)
  1. (a) Engine speed 1000 rpm or more
  2. (b) Starter signal OFF
  3. (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF

  1. A122767E04
  2. Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If there is no signal from the CKP sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is set 20 seconds after the engine is next started.

WIRING DIAGRAM

A226984E01

INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  2. Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the operation below:
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine.
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor voltage output is insufficient.
  3. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the CKP sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E32
  1. Check the CKP sensor installation.

    OK:
    Sensor is installed correctly.



NG
TIGHTEN SENSOR (Click here)
OK


4. INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT
OK

REPLACE ECM (Click here)


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Jul 2007 – Jul 2009)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (Jul 2007 – Jul 2009) →