2011-2016 FJ Cruiser · Service Manual ENGINE

P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (G signal sensor) consists of a magnet and MRE (Magneto Resistance Element).
The VVT camshaft drive gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The Crankshaft Position (CKP) sensor plate has 34 teeth. The pickup coil generates 34 signals for each engine revolution. Based on the combination of the G signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
DTC No.
DTC Detection Conditions
Trouble Areas
P0340
P0345
  1. Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more seconds have elapsed after turning ignition switch ON (1 trip detection logic)
  2. No VVT sensor signal to ECM during cranking (2 trip detection logic)
  1. Open or short in VVT sensor circuit
  2. VVT sensor
  3. Camshaft timing gear assembly
  4. Jumped tooth of timing chain
  5. ECM
P0342
P0347
Output voltage of VVT sensor 0.3 V or less for 5 seconds (1 trip detection logic)
P0343
P0348
Output voltage of VVT sensor 4.7 V or more for 5 seconds (1 trip detection logic)

  1. G035795E10
  2. Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
      Items
      Contents
      Terminals
      NE+ - NE-
      VV1+ - VV1-
      VV2+ - VV2-
      Equipment Settings
      5 V/DIV, 20 msec./DIV
      Conditions
      Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A133477E01
Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT ECM (TERMINAL VOLTAGE)
A116157E02
  1. Inspect the ECM using an oscilloscope.

    Items
    Contents
    Terminals
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Settings
    5 V/DIV, 20 msec./DIV
    Conditions
    Cranking or idling
    1. While the engine is idling, check the waveform between the terminals of the ECM connector.

      Standard Voltage:
      Tester Connections
      Specified Conditions
      VV1+ (B3-19) - VV1- (B3-29)
      Correct waveform as shown in illustration
      VV2+ (B3-18) - VV2- (B3-28)
      NE+ (B3-21) - NE- (B3-20)



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
A172864E01
  1. Disconnect the B15 or B27 VVT sensor connector.

  1. Disconnect the B1 and B3 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    VVR+ (B15-1) - VV1+ (B3-19)
    Below 1 Ω
    VVL+ (B27-1) - VV2+ (B3-18)
    VVR- (B15-2) - VV1- (B3-29)
    VVL- (B27-2) - VV2- (B3-28)
    VC (B15-3) - VC (B1-23)
    VC (B27-3) - VC (B1-23)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VVR+ (B15-1) or VV1+ (B3-19) - Body ground
    10 kΩ or higher
    VVL+ (B27-1) or VV2+ (B3-18) - Body ground
    VVR- (B15-2) or VV1- (B3-29) - Body ground
    VVL- (B27-2) or VV2- (B3-28) - Body ground
    VC (B15-3) or VC (B1-23) - Body ground
    VC (B27-3) or VC (B1-23) - Body ground

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK VVT SENSOR (SENSOR POWER SOURCE)
G038815E03
  1. Disconnect the B15 or B27 VVT sensor connector.

  1. Measure the voltage between the terminals of the VVT sensor.

    Standard Voltage:
    Tester Connection
    Specified Condition
    VC (3) - Body ground
    4.5 to 5.5 V

  1. Reconnect the VVT sensor connector.



NG
REPLACE ECM (Click here)
OK


4. CHECK SENSOR INSTALLATION (VVT SENSOR)
BR03795E39
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


5. CHECK VALVE TIMING

  1. G036290E05
    Remove the cylinder head cover (Click here or Click here).

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover (Click here or Click here).



NG
ADJUST VALVE TIMING (Click here)
OK


6. CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


7. REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 AND/OR P0348)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No output
    A
    P0340, P0342, P0343, P0345, P0347 and/or P0348
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Aug 2009)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (from Aug 2009) →