2011-2016 FJ Cruiser · Service Manual ENGINE

P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Aug 2009 – Jul 2014

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014

DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel ratio, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.
A115539E07
DTC No.
DTC Detection Condition
Trouble Area
P0136
P0156
  1. Abnormal voltage output:
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) Heated Oxygen (HO2) sensor voltage does not increase to more than 0.59 V
    1. (b) HO2 sensor voltage does not decrease to less than 0.21 V
  1. Open or short in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (for Bank 1, 2)
  3. HO2 sensor heater (for Bank 1, 2)
  4. Air-Fuel Ratio (A/F) sensor (for Bank 1, 2)
  5. Gas leak from exhaust system
  6. EFI relay
P0137
P0157
  1. Low voltage (open):
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) HO2 sensor voltage output less than 0.21 V
    1. (b) Target air-fuel ratio rich
  1. Open in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (for Bank 1, 2)
  3. HO2 sensor heater (for Bank 1, 2)
  4. Gas leak from exhaust system
  5. EFI relay
P0138
P0158
  1. High voltage (short):
    During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) HO2 sensor voltage output more than 0.59 V
    1. (b) Target air-fuel ratio lean
  1. Short in HO2 sensor (for Bank 1, 2) circuit
  2. HO2 sensor (for Bank 1, 2)
  3. Air-Fuel Ratio (A/F) sensor (for Bank 1, 2)
  4. ECM

MONITOR DESCRIPTION

  1. Active Air-Fuel Ratio Control
    The ECM usually performs air-fuel ratio feedback control so that the Air-Fuel Ratio (A/F) sensor output indicates a near stoichiometric air-fuel ratio. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).
    Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.
  1. Abnormal Voltage Output of HO2 Sensor (DTC P0136 and P0156)
    While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not decrease to less than 0.21 V and does not increase to more than 0.59 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.
    A115540E15
  1. Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157 or P0138 and P0158)
    During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the HO2 sensor has an open or short, or the voltage output of the sensor decreases significantly, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.
    While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157. When the target air-fuel ratio is lean and the voltage output is 0.59 V or more (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high, and stores DTC P0138 or P0158.

    HINT:
    The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value (Click here).

    A115541E20

  1. During normal air-fuel ratio feedback control, there are small variations in the exhaust gas oxygen concentration. In order to continuously monitor the slight variations in the HO2 sensor signal while the engine is running, the impedance* of the sensor is measured by the ECM. The ECM determines that there is a malfunction in the sensor when the measured impedance deviates from the standard range.
    *: The effective resistance in an alternating current electrical circuit.

    HINT:
    1. The impedance cannot be measured using an ohmmeter.
    2. DTC P0136 and P0156 indicate the deterioration of the HO2 sensor. The ECM stores this DTC by calculating the impedance of the sensor when the typical enabling conditions are satisfied (2 driving cycles).
    3. DTC P0137 and P0157 indicate an open or short circuit in the HO2 sensor (2 driving cycles). The ECM stores this DTC when the impedance of the sensor exceeds the threshold of 15 kΩ.


CONFIRMATION DRIVING PATTERN

  1. P0136, P0137, P0138, P0156, P0157 and P0158
A199376E01
  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Clear the DTCs.
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the tester on [A].
  7. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
  8. With the transmission in 4th gear or higher, drive the vehicle at 60 to 120 km/h (40 to 75 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / DTC/Pending [D].
  10. Read the DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.
  13. Check the DTC judgment result.
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shown ABNORMAL, the system has malfunction.
    2. If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [C] through [D].


WIRING DIAGRAM

A193213E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine.
  3. Turn the tester on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  6. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  7. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
Higher than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
Higher than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Below 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E08
A150787E01
A150788E06
-
2
A150787E01
A150790E01
A150787E01
A150788E06
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E08
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be set.
  5. If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be set.


1. READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0138 or P0158 is output
    A
    P0137 or P0157 is output
    B
    P0136 or P0156 is output
    C



B
Go to step 9

C
Go to step 7
A


2. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2 or O2S B2S2.

  1. Allow the engine to idle.

  1. Read the Heated Oxygen (HO2) sensor output voltage while idling.

    Result:
    Result
    Proceed to
    1.0 V or higher
    A
    Below 1.0 V
    B



B
Go to step 5
A


3. INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A240070E01
  1. Disconnect the HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E2)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (HO2 Sensor (bank 1))
    *2
    Component without harness connected
    (HO2 Sensor (bank 2))



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
  1. Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B50-12 (HT1B) - B47-2 (OX1B)
    Always
    10 kΩ or higher
    B50-13 (HT2B) - B47-4 (OX2B)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the intelligent tester, and monitor the voltage output of the Air-Fuel Ratio (A/F) and HO2 sensors displayed on the intelligent tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in 0.1 to 0.2% gradations within this range.
  2. The A/F sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the HO2 sensor is displayed as O2S B1S2 or O2S B2S2 on the tester.

  3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    Result 
    Tester Display (Sensor)
    Voltage Variation
    Proceed to
    AFS Voltage B1S1
    AFS Voltage B2S1
    Alternates between more and less than 3.3 V
    OK
    Remains at more than 3.3 V
    NG
    Remains at less than 3.3 V
    NG

    HINT:
    A normal HO2 sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.


    A121606E03



NG
Go to step 15
OK


6. INSPECT AIR FUEL RATIO SENSOR

HINT:
This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 3 mA in this test.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle by the drive pattern as listed below:

    1. Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or more.

    2. Drive the vehicle at 60 km/h (37 mph) or more, and decelerate the vehicle for 5 seconds or more.

    3. Repeat the deceleration above at least 3 times.A166581E46

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.

  1. Read the value of the air fuel ratio sensor current while the fuel-cut operation is performed.

    Standard:
    Less than 3.0 mA

    HINT:
    1. To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.
    2. If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the intelligent tester.



OK
Go to step 12

NG
Go to step 15
7. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / O2S B1S2 or O2S B2S2.

  1. Change the fuel injection volume using the tester, monitoring the voltage output of the HO2 sensors displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in 0.1 to 0.2% gradations within this range.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

    Standard voltage:
    Fluctuates between 0.4 V or less and 0.55 V or more.



NG
Go to step 9
OK


8. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of the Air-Fuel Ratio (A/F) and HO2 sensors displayed on the tester.

HINT:
  1. Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in 1% gradations within this range.
  2. The A/F sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the HO2 sensor is displayed as O2S B1S2 or O2S B2S2 on the intelligent tester.

  3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    Result 
    Tester Display (Sensor)
    Voltage Variation
    Proceed to
    AFS Voltage B1S1
    AFS Voltage B2S1
    Alternates between more and less than 3.3 V
    OK
    Remains at more than 3.3 V
    NG
    Remains at less than 3.3 V
    NG

    HINT:
    A normal HO2 sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.


    A121606E03



NG
Go to step 15
OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR, FUEL PRESSURE, GAS LEAK FROM SYSTEM)

9. CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leak.

    OK:
    No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


10. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A240070E01
  1. Disconnect the HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E2)
    Always
    10 kΩ or higher
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E2)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (HO2 Sensor (Bank 1))
    *2
    Component without harness connected
    (HO2 Sensor (Bank 2))



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


11. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the HO2 sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B54-1 (HT1B) - B50-12 (HT1B)
    Always
    Below 1 Ω
    B54-3 (OX1B) - B47-2 (OX1B)
    Always
    Below 1 Ω
    B54-4 (E2) - B47-1 (EX1B)
    Always
    Below 1 Ω
    B34-1 (HT2B) - B50-13 (HT2B)
    Always
    Below 1 Ω
    B34-3 (OX2B) - B47-4 (OX2B)
    Always
    Below 1 Ω
    B34-4 (E2) - B47-3 (EX2B)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B54-1 (HT1B) or B50-12 (HT1B) - Body ground
    Always
    10 kΩ or higher
    B54-3 (OX1B) or B47-2 (OX1B) - Body ground
    Always
    10 kΩ or higher
    B54-4 (E2) or B47-1 (EX1B) - Body ground
    Always
    10 kΩ or higher
    B34-1 (HT2B) or B50-13 (HT2B) - Body ground
    Always
    10 kΩ or higher
    B34-3 (OX2B) or B47-4 (OX2B) - Body ground
    Always
    10 kΩ or higher
    B34-4 (E2) or B47-3 (EX2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


13. PERFORM CONFIRMATION DRIVING PATTERN
  1. Perform the CONFIRMATION DRIVING PATTERN (P0136, P0137, P0138, P0156, P0157 and P0158).


NEXT


14. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed.

    Result 
    Result
    Proceed to
    ABNORMAL
    (P0136, P0137, P0138, P0156, P0157 or P0158 detected)
    A
    NORMAL
    (No DTC output)
    B



B
END
A

REPLACE AIR FUEL RATIO SENSOR (Click here)

15. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


16. PERFORM CONFIRMATION DRIVING PATTERN
  1. Perform the CONFIRMATION DRIVING PATTERN (P0136, P0137, P0138, P0156, P0157 and P0158).


NEXT


17. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed.

    Result 
    Result
    Proceed to
    ABNORMAL
    (P0136, P0137, P0138, P0156, P0157 or P0158 detected)
    A
    NORMAL
    (No DTC output)
    B



B
END
A

REPLACE HEATED OXYGEN SENSOR (Click here)


← P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ 5 more codes) (Dec 2007 – Jul 2009)P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ 5 more codes) (from Aug 2014) →