2011-2016 FJ Cruiser · Service Manual ENGINE

P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.
A115539E03
DTC No.
DTC Detection Condition
Trouble Area
P0136
P0156
During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)
  1. (a) Heated Oxygen (HO2) sensor voltage does not decrease to less than 0.21 V
  2. (b) HO2 sensor voltage does not increase to more than 0.59 V
  1. Open or short in HO2 sensor (bank 1 and 2, sensor 2) circuit
  2. HO2 sensor (bank 1 and 2, sensor 2)
  3. HO2 sensor heater (bank 1 and 2, sensor 2)
  4. Air Fuel Ratio (A/F) sensor (bank 1and 2, sensor 1)
  5. EFI relay
  6. Gas leak from exhaust system
P0137
P0157
During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)
  1. (a) HO2 sensor voltage output less than 0.21 V
  2. (b) Target air fuel ratio rich
  1. Open in HO2 sensor (bank 1 and 2, sensor 2) circuit
  2. HO2 sensor (bank 1 and 2, sensor 2)
  3. HO2 sensor heater (bank 1 and 2, sensor 2)
  4. Air Fuel Ratio (A/F) sensor (bank 1and 2, sensor 1)
  5. Gas leak from exhaust system
P0138
P0158
During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)
  1. (a) HO2 sensor voltage output 0.59 V or more
  2. (b) Target air-fuel ratio lean
  1. Short in HO2 sensor (bank 1 and 2, sensor 2) circuit
  2. HO2 sensor (bank 1 and 2, sensor 2)
  3. ECM internal circuit malfunction
  4. A/F sensor (bank 1and 2, sensor 1)

MONITOR DESCRIPTION


Active Air Fuel Ratio Control
The ECM usually performs air fuel ratio feedback control so that the Air Fuel Ratio (A/F) sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect Heated Oxygen (HO2) sensor malfunctions.
Active air fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, either of the following DTCs is set: DTC P0137 or P0157 (open circuit).

Abnormal Voltage Output of HO2 Sensor (DTCs P0136 and P0156)
While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not decrease to less than 0.21 V and does not increase to more than 0.59 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and sets DTCs P0136 and P0156.
A115540E01

Open or Short in Heated Oxygen (HO2) Sensor Circuit (DTCs P0137 and P0157 or P0138 and P0158)
During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.
If the HO2 sensor has an open or short, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the HO2 sensor output does not change.
While performing active air fuel ratio control, when the target air fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and sets DTC P0137 or P0157. When the target air-fuel ratio is lean and the voltage output is 0.59 V or more (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high, and sets DTC P0138 or P0158.

HINT:
*: The TWC has the capability to store oxygen. When active air fuel ratio control is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.

A115541E01

WIRING DIAGRAM

A133412E03

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation pattern will activate the heated oxygen sensor monitor. This is useful for verifying the completion of the repair.

A164766E24
  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester ON.
  4. Clear DTCs (Click here).
  5. Switch the ECM from normal mode to check mode (Click here).
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S (A/FS) Monitor.
  7. Check that the item O2S (A/FS) Monitor display Incmpl.
  8. Start the engine and warm it up (Proceed to "A").
  9. Drive the vehicle at 60 to 120 km/h (37 to 75 mph) for 10 minutes or more (Proceed to "B").
  10. Note the state of the Data List items. Those items will change to Compl as the O2 sensor monitor operates.
  11. Enter the following menus: Powertrain / Engine and ECT / DTC and check if any DTCs (any pending DTCs) are output.

HINT:
If the item O2S (A/FS) Monitor does not change to Compl, and any pending DTCs fail to output, extend the driving time.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor function using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2, and then press the View button.

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0138 or P0158
    A
    P0137 or P0157
    B
    P0136 or P0156
    C



B
Go to step 8

C
Go to step 6
A


2. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1S2 or O2S B2S2.

  1. Allow the engine to idle.

  1. Read the Heated Oxygen (HO2) sensor output voltage while idling.

    Result 
    Result
    Proceed to
    1.0 V or more
    A
    Less than 1.0 V
    B



B
Go to step 5
A


3. INSPECT OXYGEN SENSOR (CHECK FOR SHORT)

  1. A187361E01
    Disconnect the HO2 sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for Bank 1):
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 4 (E2)
    Always
    10 kΩ or higher
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher

    Standard Resistance (for Bank 2):
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 4 (E2)
    Always
    10 kΩ or higher
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

  1. A187141E01
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-1 (HT1B) - B1-18 (OX1B)
    Always
    10 kΩ or higher
    B2-5 (HT2B) - B2-33 (OX2B)
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK AIR FUEL RATIO SENSOR (CURRENT)

HINT:
This A/F sensor test is to check the A/F sensor current during the fuel-cut. When the sensor is normal, the sensor current will indicate below 3.0 mA in this test.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / AFS B1 S1 or AFS B2 S1.

  1. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.

  1. Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this at least 3 times.

  1. Read the value.

    Standard Current:
    Less than 3.0 mA

A166581E03


OK
Go to step 11

NG
Go to step 14
6. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2 or O2S B2S2.

  1. After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.

  1. Read the output voltage of the HO2 sensor when the engine speed is suddenly increased.

    HINT:
    Quickly accelerate the engine to 4000 rpm 3 times using the accelerator pedal.

    Standard Voltage:
    Fluctuates between 0.4 V or less and 0.5 V or higher.



NG
Go to step 8
OK


7. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of Air Fuel Ratio (A/F) and HO2 sensors displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within the range.
    2. The A/F sensor is displayed as AFS B1 S1 or AFS B2 S1, and the HO2 sensor is displayed as O2S B1 S2 or O2S B2 S2, on the intelligent tester.
      Result 
      Result
      Voltage Variation
      Proceed to
      AFS B1 S1 (A/F)
      AFS B2 S1 (A/F)
      Alternates between higher than and below 3.3 V
      OK
      Remains at higher than 3.3 V
      NG
      Remains at below 3.3 V
      NG

    HINT:
    A normal HO2 sensor voltage (O2S B1 S2 or O2S B2 S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either below or higher than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.

A121606E03


NG
Go to step 14
OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

8. CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


9. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A187361E02
  1. Disconnect the HO2 sensor connector.

  1. Measure the resistance between the terminals of the HO2 sensor connector.

    Standard Resistance (for Bank 1):
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E2)
    Always
    10 kΩ or higher

    Standard Resistance (for Bank 2):
    Tester Connection
    Condition
    Specified Condition
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E2)
    Always
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A187142E01
  1. Disconnect the HO2 sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Terminal Connection
    Switch Condition
    Specified Condition
    B36-2 (+B) - Body ground
    Ignition Switch ON
    11 to 14 V
    B34-2 (+B) - Body ground
    Ignition Switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance :
    Terminal Connection
    Condition
    Specified Condition
    B36-1 (HT1B) - B1-1 (HT1B)
    Always
    Below 1 Ω
    B36-3 (OX1B) - B1-18 (OX1B)
    Always
    Below 1 Ω
    B36-4 (E2) - B1-28 (E2)
    Always
    Below 1 Ω
    B34-1 (HT2B) - B2-5 (HT2B)
    Always
    Below 1 Ω
    B34-3 (OX2B) - B2-33 (OX2B)
    Always
    Below 1 Ω
    B34-4 (E2) - B1-28 (E2)
    Always
    Below 1 Ω
    B36-1 (HT1B) or B1-1 (HT1B) - Body ground
    Always
    10 kΩ or higher
    B36-3 (OX1B) or B1-18 (OX1B) - Body ground
    Always
    10 kΩ or higher
    B34-1 (HT2B) or B2-5 (HT2B) - Body ground
    Always
    10 kΩ or higher
    B34-3 (OX2B) or B2-33 (OX2B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connectors.A103832E85



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


12. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


13. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check the DTC MONITOR is "NORMAL". If DTC Monitor is "INCOMPLETE", perform the drive pattern increasing the vehicle speed and using second gear to decelerate the vehicle.

    Result 
    Result
    Proceed to
    NORMAL
    (No DTC output)
    A
    ABNORMAL
    (P0136, P0137, P0138, P0156, P0157 or P0158 detected)
    B



B
REPLACE AIR FUEL RATIO SENSOR (Click here)
A

END

14. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


16. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.

  1. Check the DTC MONITOR is "NORMAL". If DTC Monitor is "INCOMPLETE", perform the drive pattern increasing the vehicle speed and using second gear to decelerate the vehicle.

    Result 
    Result
    Proceed to
    NORMAL
    (No DTC output)
    A
    ABNORMAL
    (P0136, P0137, P0138, P0156, P0157 or P0158 detected)
    B



B
REPLACE HEATED OXYGEN SENSOR (Click here)
A

END


← P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (Dec 2007 – Jul 2009)P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ 5 more codes) (Aug 2009 – Jul 2014) →