P0100 Mass or Volume Air Flow Circuit
Diagnostic trouble codes · Vehicles built Jul 2007 – Nov 2007
Also covers:
- P0102 Mass or Volume Air Flow Circuit Low Input
- P0103 Mass or Volume Air Flow Circuit High Input
Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009
DESCRIPTION
The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.The ECM uses this information to determine the fuel injection time and to provide appropriate air fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.
- HINT:
- When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0100 |
Open or short in Mass Air Flow (MAF) meter circuit for 3 seconds when engine speed less than 4000 rpm (1 trip detection logic) |
|
| P0102 |
Open in Mass Air Flow (MAF) meter circuit for 3 seconds when engine speed less than 4000 rpm (1 trip detection logic) |
|
| P0103 |
Short in Mass Air Flow (MAF) meter circuit for 3 seconds when engine speed less than 4000 rpm (1 trip detection logic) |
|
- HINT:
- When any of these DTCs are set, check the air-flow rate by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / MAF.
Mass Air Flow Rate (g/sec)
Malfunctions
Approximately 0.0
- Open in Mass Air Flow (MAF) meter power source circuit
- Open or short in VG circuit
271.0 or more
- Open in EVG circuit
- Open in Mass Air Flow (MAF) meter power source circuit
MONITOR DESCRIPTION
If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and sets a DTC.Example:
When the sensor voltage output remains less than 0.2 V, or more than 4.9 V, for more than 3 seconds, the ECM sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 3 seconds after the engine is next started.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE) |
Connect an intelligent tester to the DLC3.
Start the engine.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.
Read the values displayed on the tester.
- Result:
Mass Air Flow Rate (g/sec)
Proceed To
0.0
A
271.0 or more
B
Between 1.0 and 270.0 (*1)
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE) |
![]() ![]() |
Disconnect the B13 Mass Air Flow (MAF) meter connector.
Turn the ignition switch ON.
Measure the voltage between the terminal of the wire harness side connector and body ground.
- Standard Voltage:
Tester Connections
Specified Conditions
+B (B13-1) - Body ground
11 to 14 V
Reconnect the MAF meter connector.
|
|
||||
| OK | |
| 3. INSPECT ECM (VG VOLTAGE) |
![]() ![]() |
Start the engine.
Measure the voltage between the terminals of the B1 ECM connector.
- HINT:
- The transmission gear should be in the neutral and the A/C switch should be turned OFF.
- Standard Voltage:
Tester Connections
Conditions
Specified Conditions
VG (B1-30) - E2G (B1-29)
Engine idling
0.5 to 3.0 V
|
|
||||
| NG | |
| 4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() ![]() |
Disconnect the B13 MAF meter connector.
Disconnect the B1 ECM connector.
Check the resistance.
- Standard Resistance (Check for open):
Tester Connections
Specified Conditions
VG (B13-3) - VG (B1-30)
Below 1 Ω
E2G (B13-2) - E2G (B1-29)
- Standard Resistance (Check for short):
Tester Connections
Specified Conditions
VG (B13-3) or VG (B1-30) - Body ground
10 kΩ or higher
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - EFI RELAY) |
![]() ![]() |
Inspect the EFI NO. 2 fuse.
Remove the EFI NO. 2 fuse from the engine room relay block.
Check the EFI NO. 2 fuse resistance.
- Standard Resistance:
- Below 1 Ω
Reinstall the EFI NO. 2 fuse.
Disconnect the B13 MAF meter connector.
Remove the EFI relay from the engine room relay block.
Check the resistance.
- Standard Resistance (Check for open):
Tester Connections
Specified Conditions
+B (B13-1) - EFI relay (3)
Below 1 Ω
- Standard Resistance (Check for short):
Tester Connections
Specified Conditions
+B (B13-1) or EFI relay (3) - Body ground
10 kΩ or higher
Reconnect the MAF meter connector.
Reinstall the EFI relay.
|
|
||||
| OK | ||
| ||
| 6. INSPECT ECM (SENSOR GROUND) |
![]() ![]() |
Check the resistance.
- Standard Resistance:
Tester Connections
Specified Conditions
E2G (B1-29) - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() ![]() |
Disconnect the B13 MAF meter connector.
Disconnect the B1 ECM connector.
Check the resistance.
- Standard Resistance (Check for open):
Tester Connections
Specified Conditions
VG (B13-3) - VG (B1-30)
Below 1 Ω
E2G (B13-2) - E2G (B1-29)
- Standard Resistance (Check for short):
Tester Connections
Specified Conditions
VG (B13-3) or VG (B1-30) - Body ground
10 kΩ or higher
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||






