2011-2016 FJ Cruiser · Service Manual ENGINE

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be output.

WIRING DIAGRAM

A226161E01

INSPECTION PROCEDURE

HINT:
Using the intelligent tester to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/
Range (Display)
Normal Condition
Diagnostic Note
STOP LIGHT SW
(Stop Light Switch)
Stop light switch status/
ON or OFF
  1. Brake pedal is depressed: ON
  2. Brake pedal is released: OFF
-

1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch.

  1. Read the values displayed on the tester.

    OK:
    Tester Display
    Measurement Item: Range (display)
    Normal Condition
    Stop Light Switch
    Stop light switch status:
    ON or OFF
    1. ON: Brake pedal is depressed
    2. OFF: Brake pedal is released



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT STOP LIGHT SWITCH
A115657E22
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin not pushed
    10 kΩ or higher
    Pin pushed
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Stop Light Switch)



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

  1. A226162E02
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E81-18 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    E81-18 (STP) - Body ground
    Brake pedal is released
    Below 1 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0724 Brake Switch "B" Circuit High (Jul 2007 – Jul 2009)P0724 Brake Switch "B" Circuit High (from Nov 2010) →