2011-2016 FJ Cruiser · Service Manual ENGINE

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling, while driving in lock-up condition, when brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signals to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Conditions
Trouble Areas
P0724
The stop light switch remains ON even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during "stop and go" driving, the ECM interprets this as a fault in the stop light switch, the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h [1.86 mph]) and go (30 km/h [18.65 mph] or more) 5 times during 2 driving cycles, in order to detect a malfunction.

WIRING DIAGRAM

A133421E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the values displayed on the tester.

OK:
Conditions
Stop Light Switch
Brake pedal is depressed
ON
Brake pedal is released
OFF



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
A072924E09
  1. Remove the stop light switch assembly.

  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Switch Positions
    Specified Conditions
    1 - 2
    Switch pin free
    Below 1 Ω
    3 - 4
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
A116299E03
  1. Disconnect the A3 stop light switch connector.

  1. Disconnect the E47 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    Stop light switch (A3-1) - STP (E47-15)
    Below 1 Ω
    Stop light switch (A3-4) - ST1- (E47-16)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    Stop light switch (A3-1) or STP (E47-15) - Body ground
    10 kΩ or higher
    Stop light switch (A3-4) or ST1- (E47-16) - Body ground

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (Dec 2007 – Jul 2009)P0724 Brake Switch "B" Circuit High (Aug 2009 – Oct 2010) →