2011-2016 FJ Cruiser · Service Manual ENGINE

P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built Jul 2007 – Nov 2007

Also covers:

DESCRIPTION

HINT:
Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a Heated Oxygen (HO2) sensor is used.
The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.
A115539E03
DTC No.
DTC Detection Conditions
Trouble Areas
P0137
P0157
During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)
  1. (a) Heated Oxygen (HO2) sensor voltage output less than 0.21 V
  2. (b) Target air fuel ratio rich
  1. Open in HO2 sensor (bank 1 and 2, sensor 2) circuit
  2. HO2 sensor (bank 1 and 2, sensor 2)
  3. HO2 sensor heater (bank 1 and 2, sensor 2)
  4. Gas leak from exhaust system

MONITOR DESCRIPTION


Active Air Fuel Ratio Control
The ECM usually performs air fuel ratio feedback control so that the Air Fuel Ratio (A/F) sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect Heated Oxygen (HO2) sensor malfunctions.
Active air fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, either of the following DTCs is set: DTC P0137 or P0157 (open circuit).

Open in Heated Oxygen (HO2) Sensor Circuit
During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.
If the HO2 sensor has an open or short, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the HO2 sensor output does not change.
While performing active air fuel ratio control, when the target air fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and sets DTC P0137 or P0157.

HINT:
*: The TWC has the capability to store oxygen. When active air fuel ratio control is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.

A172862E01

WIRING DIAGRAM

A133412E02

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation pattern will activate the heated oxygen sensor monitor. This is useful for verifying the completion of the repair.

A172863E01
  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch ON.
  3. Turn the tester ON.
  4. Clear DTCs (Click here).
  5. Switch the ECM from normal mode to check mode (Click here).
  6. Select the following menu items: Powertrain / Engine and ECT / Data List / O2S (A/FS) Monitor.
  7. Check that the item O2S (A/FS) Monitor displays Incmpl (Incomplete).
  8. Start the engine and warm it up. (Proceed to "A")
  9. Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) for at least 10 minutes. (Proceed to "B")
  10. Note the state of the Data List items. Those items will change to Compl (Complete) as the O2 Sensor monitor operates.
  11. On the tester, select the following menu items: Powertrain / Engine and ECT / DTC and check if any DTCs (any pending DTCs) are set.

HINT:
If the item O2S (A/FS) Monitor does not change to Compl (Complete), and any pending DTCs fail to set, extend the driving time.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor function using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2, and then press the View button.

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0137 AND P0157)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0137 or P0157
    A
    P0137 or P0157, and other DTCs
    B

    HINT:
    If any DTCs other than P0137 and P0157 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


3. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A062378E39
  1. Disconnect the B34 or B36 HO2 sensor connector.

  1. Measure the resistance between the terminals of the HO2 sensor connector.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    HT1B or HT2B (1) - +B (2)
    11 to 16 Ω at 20°C (68°F)
    HT1B or HT2B (1) - E2 (4)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A116170E04
  1. Disconnect the B34 or B36 HO2 sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the +B terminal of the HO2 sensor connector and body ground.

    Standard Voltage:
    Terminal Connections
    Specified Conditions
    +B (B36-2) - Body ground
    11 to 14 V
    +B (B34-2) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the B1 and B2 ECM connectors.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Terminal Connections
    Specified Conditions
    HT1B (B36-1) - HT1B (B1-1)
    Below 1 Ω
    OX1B (B36-3) - OX1B (B1-18)
    E2 (B36-4) - E2 (B1-28)
    HT2B (B34-1) - HT2B (B2-5)
    OX2B (B34-3) - OX2B (B2-33)
    E2 (B34-4) - E2 (B1-28)

    Standard Resistance (Check for short):
    Terminal Connections
    Specified Conditions
    HT1B (B36-1) or HT1B (B1-1) - Body ground
    10 kΩ or higher
    OX1B (B36-3) or OX1B (B1-18) - Body ground
    HT2B (B34-1) or HT2B (B2-5) - Body ground
    OX2B (B34-3) or OX2B (B2-33) - Body ground

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connectors.A103832E33



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


6. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0137 OR P0157)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input DTCs: P0137 and P0157.

  1. Check the DTC MONITOR is "NORMAL." If DTC Monitor is "INCOMPLETE," perform the drive pattern adding the vehicle speed and using second gear to decelerate the vehicle.

    Result:
    Display (DTC Output)
    Proceed To
    NORMAL
    (No DTC output)
    A
    ABNORMAL
    (P0137 or P0157 detected)
    B



B
REPLACE AIR FUEL RATIO SENSOR (Click here)
A

END


← P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ 5 more codes) (from Aug 2014)P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (Dec 2007 – Jul 2009) →