2011-2016 FJ Cruiser · Service Manual ENGINE

P0171 System Too Lean (Bank 1)

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short- term fuel trim compensation.
If both the short-term and long-term fuel trims are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and stores a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic)
  1. Air induction system
  2. Fuel injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  8. A/F sensor (bank 1, 2 sensor 1)
  9. A/F sensor heater (bank 1, 2 sensor 1)
  10. A/F sensor heater relay
  11. A/F sensor heater relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic)
  1. Fuel injector leak or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  8. A/F sensor (bank 1, 2 sensor 1)
  9. A/F sensor heater (bank 1, 2 sensor 1)
  10. A/F sensor heater relay
  11. A/F sensor heater relay circuits
  12. ECM

HINT:
  1. When DTC P0171 or P0174 is stored, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air- fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learning value is more than +35% or less than -35%, the ECM interprets this as a fuel system malfunction.
A121607E01

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. (1) Connect the intelligent tester to the DLC3.
  2. (2) Start the engine and turn the tester ON.
  3. (3) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. (4) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. (5) Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (6) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

    Standard:
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25%
    Rich
    Less than 3.0 V
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5%
    Lean
    More than 3.35 V
    O2S B1S2 or O2S B2S2
    (HO2)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Less than 0.4 V

NOTICE:
The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor / A/F Control System / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2, then press View button.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175
    A
    P0171, P0172, P0174 or P0175 and other DTCs
    B

    HINT:
    If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak.

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

  1. Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


    Standard:
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25%
    Rich
    Less than 3.0 V
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5%
    Lean
    More than 3.35 V
    O2S B1S2 or O2S B2S2
    (HO2)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Less than 0.4 V

    Result 
    Status
    AFS B1S1
    or
    AFS B2S1
    Status
    O2S B1S2
    or
    O2S B2S2
    A/F Condition and
    A/F Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    C
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector blockage
    4. Gas leak from exhaust system
    5. Air induction system
    6. Fuel pressure
    7. Mass Air Flow (MAF) meter
    8. Engine Coolant Temperature (ECT) sensor
    A
    Rich
    Rich
    Actual air-fuel ratio rich
    -
    1. Fuel injector leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. MAF meter
    6. ECT sensor
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    Lean: During Control the Injection Volume for A/F sensor, the A/F sensor output voltage (AFS) is consistently more than 3.35 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.Rich: During Control the Injection Volume for A/F sensor, the AFS is consistently less than 3.0 V, and the O2S is consistently more than 0.55 V.Lean/Rich: During Control the Injection Volume for A/F sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



B
Go to step 11

C
Go to step 15
A


5. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: 80°C to 100°C (176°C to 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6. READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Read the values using the intelligent tester (MAF).

    NOTICE:
    1. Turn the ignition switch off.
    2. Perform the inspection with the vehicle indoors and on a level surface.
    3. Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
    4. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON (do not start the engine).

    3. Turn the tester ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

    5. Wait for 30 seconds, and read the values on the tester.

      Standard value:
      Less than 0.92 g/sec

  1. Inspect the mass air flow meter.

    1. Remove the mass air flow meter (Click here).

    2. A172049E02
      Using a work light, check that the platinum filament (heater portion) in the mass air flow meter has no foreign matter attached.

      OK:
      No foreign matter attached

    3. Reinstall the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


7. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8. CHECK EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9. CHECK SPARK AND IGNITION
  1. Check the spark and ignition (Click here).

HINT:
If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10. INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Inspect the fuel injector assembly (Click here).

HINT:
If the fuel injectors malfunction, engine misfire may occur. The misfire count can be read using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


11. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A187143E01
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Bank 1 Sensor 1):
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A ) - 2 (+B)
    20°C (68°F)
    1.8 Ω to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher

    Standard Resistance (Bank 2 Sensor 1):
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 Ω to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12. INSPECT AIR FUEL RATIO SENSOR HEATER RELAY
B016200E02
  1. Remove the A/F sensor heater relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage not applied
    10 kΩ or higher
    When battery voltage applied to terminal 1 and 2
    Below 1 Ω

  1. Reinstall the A/F sensor heater relay.



NG
REPLACE AIR FUEL RATIO SENSOR HEATER RELAY
OK


13. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A187144E01
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B33-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B31-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) - B2-2 (HA1A)
    Always
    Below 1 Ω
    B33-3 (A1A+) - B2-22 (A1A+)
    Always
    Below 1 Ω
    B33-4 (A1A-) - B2-30 (A1A-)
    Always
    Below 1 Ω
    B31-1 (HA2A) - B2-1 (HA2A)
    Always
    Below 1 Ω
    B31-3 (A2A+) - B2-23 (A2A+)
    Always
    Below 1 Ω
    B31-4 (A2A-) - B2-31 (A2A-)
    Always
    Below 1 Ω
    B33-1 (HA1A) or B2-2 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B33-3 (A1A+) or B2-22 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B33-4 (A1A-) or B2-30 (A1A-) - Body ground
    Always
    10 kΩ or higher
    B31-1 (HA2A) or B2-1 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B31-3 (A2A+) or B2-23 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B31-4 (A2A-) or B2-31 (A2A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.A133442E02



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the A/F sensor (Click here).


NEXT


15. PERFORM CONFIRMATION DRIVING PATTERN

  1. A185027E06
  2. (a) Connect the intelligent tester to the DLC3.
  3. (b) Turn the ignition switch to ON and turn the tester ON.
  4. (c) Clear DTCs (Click here).
  5. (d) Switch the ECM from normal mode to check mode using the tester (Click here).
  6. (e) Start the engine and warm it up with all the accessories switched OFF.
  7. (f) Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes.

    HINT:
    If the system is still malfunctioning, the MIL will be illuminated during step (f).

    NOTICE:
    If the conditions in this test are not strictly followed, no malfunction should be detected.


NEXT


16. CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

Result 
Result
Proceed to
No output
A
P0171, P0172, P0174 or P0175
B


B
REPLACE ECM (Click here)
A

END


← P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) (+ P0157) (Jul 2007 – Nov 2007)P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (Aug 2009 – Oct 2010) →