2011-2016 FJ Cruiser · Service Manual ENGINE

P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built Aug 2009 – Jul 2014

Also covers:

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P2195 (Click here).

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. When one of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  4. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.

    A226853E01

DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A
(1 trip detection logic)
  1. Open in A/F sensor heater circuit
  2. A/F sensor heater (for Sensor 1)
  3. A/F sensor heater relay
  4. ECM
P0032
P0052
Air-Fuel Ratio (A/F) sensor heater current failure
(1 trip detection logic)
  1. Short in A/F sensor heater circuit
  2. A/F sensor heater (for Sensor 1)
  3. A/F sensor heater relay
  4. ECM
P101D
P103D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
ECM

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM uses information from the Air-Fuel Ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.
The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.
When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E28
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (A/F Sensor)



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2. CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
A150242E31
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B33-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B31-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to A/F Sensor)
    *2
    for Bank 1
    *3
    for Bank 2



B
Go to step 5
A


3. INSPECT AIR FUEL RATIO SENSOR HEATER RELAY

  1. B016200E02
    Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE AIR FUEL RATIO SENSOR HEATER RELAY
OK


4. CHECK HARNESS AND CONNECTOR (A/F HEATER RELAY - A/F SENSOR AND BODY GROUND)
  1. Disconnect the A/F sensor connector.

  1. Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B33-2 (+B) - A/F HEATER relay terminal 3
    Always
    Below 1 Ω
    B31-2 (+B) - A/F HEATER relay terminal 3
    Always
    Below 1 Ω
    A/F HEATER relay terminal 2 - Body ground
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B33-2 (+B) or A/F HEATER relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B31-2 (+B) or A/F HEATER relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)

5. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
  1. Disconnect the A/F sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) - B50-17 (HA1A)
    Always
    Below 1 Ω
    B31-1 (HA2A) - B50-19 (HA2A)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) or B50-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B31-1 (HA2A) or B50-19 (HA2A) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Read the output DTCs using the tester.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC P0031, P0032, P0051, P0052, P101D or P103D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032, P0051, P0052) (Dec 2007 – Jul 2009)P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ 5 more codes) (from Aug 2014) →