2011-2016 FJ Cruiser · Service Manual ENGINE

P0171 System Too Lean (Bank 1)

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim is considerably in error to lean side (2 trip detection logic)
  1. Air induction system
  2. Injector blockage
  3. Mass Air Flow (MAF) meter
  4. Engine Coolant Temperature (ECT) sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  8. A/F sensor (bank 1, 2 sensor 1)
  9. A/F sensor heater (bank 1, 2 sensor 1)
  10. A/F sensor heater relay
  11. A/F sensor heater and A/F sensor heater relay circuits
  12. PCV valve and hose
  13. PCV hose connections
  14. ECM
P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim is considerably in error to rich side (2 trip detection logic)
  1. Injector leak or blockage
  2. MAF meter
  3. ECT sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in A/F sensor (bank 1, 2 sensor 1) circuit
  8. A/F sensor (bank 1, 2 sensor 1)
  9. A/F sensor heater (bank 1, 2 sensor 1)
  10. A/F sensor heater relay
  11. A/F sensor heater and A/F sensor heater relay circuits
  12. ECM

HINT:
  1. When DTC P0171 or P0174 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air- fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this a fault in the fuel system and sets a DTC.
Example:
The average fuel trim learning value is +35% or more, or -35% or less, the ECM interprets this as a fuel system malfunction.
A121607E01

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine.
  3. Turn the tester on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  6. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  7. Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+25%
Rich
Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
Higher than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
Higher than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Below 0.4 V

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E04
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E04
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)

HINT:
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
  3. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be set.
  5. If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be set.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0171, P0172, P0174 or P0175 is output
    A
    P0171, P0172, P0174 or P0175 and other DTCs are output
    B

HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leaks from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The A/F sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

    Tester Display (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (A/F)
    +25%
    Rich
    Below 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1
    (A/F)
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (HO2)
    +25%
    Rich
    Higher than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Below 0.4 V
    Result 
    Status AFS Voltage B1S1 or AFS Voltage B2S1
    Status O2S B1S2 or O2S B2S2
    A/F Condition and A/F Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    A
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Injector blockage
    4. Gas leak from exhaust system
    5. Air induction system
    6. Fuel pressure
    7. Mass Air Flow (MAF) meter
    8. Engine Coolant Temperature (ECT) sensor
    A
    Rich
    Rich
    Actual air-fuel ratio rich
    -
    1. Injector leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. MAF meter
    6. ECT sensor
    A
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    A/F sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    -
    A/F sensor
    B
    Lean: During Control the Injection Volume for A/F Sensor, the A/F sensor output voltage (AFS) is consistently more than 3.4 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



B
Go to step 11
A


5. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 80°C and 100°C (176°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6. READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Read the values using the intelligent tester.

    NOTICE:
    1. Turn the ignition switch to off.
    2. Perform the inspection with the vehicle indoors and on a level surface.
    3. Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
    4. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

  1. Connect the tester to the DLC3.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Wait for 30 seconds, and read the values on the intelligent tester.

    Standard:
    Less than 0.92 g/sec



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


7. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8. CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


9. CHECK FOR SPARKS AND IGNITION
  1. Check for sparks and ignition (Click here).



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10. INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the fuel injector (Click here).



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
11. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E28
  1. Disconnect the A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (A/F Sensor)



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12. CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
A150242E31
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B33-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B31-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to A/F Sensor)
    *2
    for Bank 1
    *3
    for Bank 2



NG
Go to step 18
OK


13. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
  1. Disconnect the A/F sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) - B50-17 (HA1A)
    Always
    Below 1 Ω
    B33-3 (A1A+) - B49-1 (A1A+)
    Always
    Below 1 Ω
    B33-4 (A1A-) - B49-2 (A1A-)
    Always
    Below 1 Ω
    B31-1 (HA2A) - B50-19 (HA2A)
    Always
    Below 1 Ω
    B31-3 (A2A+) - B49-7 (A2A+)
    Always
    Below 1 Ω
    B31-4 (A2A-) - B49-8 (A2A-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B33-1 (HA1A) or B50-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B33-3 (A1A+) or B49-1 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B33-4 (A1A-) or B49-2 (A1A-) - Body ground
    Always
    10 kΩ or higher
    B31-1 (HA2A) or B50-19 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B31-3 (A2A+) or B49-7 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B31-4 (A2A-) or B49-8 (A2A-) - Body ground
    Always
    10 kΩ or higher

    A226853E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the A/F sensor (Click here).


NEXT


15. CHECK WHETHER DTC OUTPUT RECURS (DTC P171,P0172,P0174 OR P0175)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Start the engine and warm it up.

  1. With the engine warmed up, idle the engine for 2 minutes or more.

  1. Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 5 minutes or more.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0171, P0172, P0174 or P0175.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (DTC P0171, P0172, P0174 or P0175 is output)
    A
    NORMAL (No DTC is output)
    B



B
END
A


16. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


17. CHECK WHETHER DTC OUTPUT RECURS (DTC P171,P0172,P0174 OR P0175)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up.

  1. With the engine warmed up, idle the engine for 2 minutes or more.

  1. Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 5 minutes or more.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0171, P0172, P0174 or P0175.

  1. Check the DTC judgment result.

Result 
Tester Display
Description
NORMAL
  1. DTC judgment completed
  2. System normal
ABNORMAL
  1. DTC judgment completed
  2. System abnormal
INCOMPLETE
  1. DTC judgment not completed
  2. Perform driving pattern after confirming DTC enabling conditions
UNKNOWN
  1. Unable to perform DTC judgment
  2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

NEXT

END

18. CHECK HARNESS AND CONNECTOR (A/F HEATER RELAY - A/F SENSOR)
  1. Disconnect the A/F sensor connector.

  1. Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B33-2 (+B) - A/F HEATER relay terminal 3
    Always
    Below 1 Ω
    B31-2 (+B) - A/F HEATER relay terminal 3
    Always
    Below 1 Ω
    A/F HEATER relay terminal 2 - Body ground
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B33-2 (+B) or A/F HEATER relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B31-2 (+B) or A/F HEATER relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19. INSPECT AIR FUEL RATIO SENSOR HEATER RELAY

  1. B016200E02
    Remove the A/F HEATER relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE AIR FUEL RATIO SENSOR HEATER RELAY
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (Dec 2007 – Jul 2009)P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (from Nov 2010) →