2011-2016 FJ Cruiser · Service Manual ENGINE

ACIS Control Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Jul 2009

DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
When the engine speed is between 2,200 rpm and 4,100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status), to close the IACV. Under other conditions, the VSV is usually OFF and the IACV is open.
A115903E01

WIRING DIAGRAM

A133431E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE VSV FOR ACIS)
A067588E05
  1. Disconnect the vacuum hose.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control. Operate the VSV for ACIS.

  1. Check the VSV operation when it is operated using an intelligent tester.

    OK:
    Tester Operations
    Specified Conditions
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

  1. Reconnect the vacuum hose.



OK
Go to step 4
NG


2. INSPECT VSV FOR ACIS (OPERATION)

  1. A054315E03
    Check that air flows from port E to the air filter.

    OK:
    Air from port E flows out through the air filter.

  1. A054316E03
    Apply the battery positive voltage across the terminals.

  1. Check that air flows from port E to port F.

    OK:
    Air from port E flows out through port F.



NG
REPLACE VSV FOR ACIS (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM, VSV FOR ACIS - EFI RELAY)
A133467E03
  1. Check the wire harness and connectors between the VSV for ACIS and ECM.

    1. Disconnect the B17 VSV for ACIS connector.

    2. Disconnect the B1 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      VSV for ACIS (B17-2) - ACIS (B1-33)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      VSV for ACIS (B17-2) or ACIS (B1-33) - Body ground
      10 kΩ or higher

    4. Reconnect the VSV for ACIS connector.

    5. Reconnect the ECM connector.

  1. Check the wire harness between the VSV for ACIS and EFI relay.

    1. Disconnect the B17 VSV for ACIS connector.

    2. Remove the EFI relay from the engine room relay block.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      VSV for ACIS (B17-1) - EFI relay terminal 3
      Below 1 Ω

    4. Reconnect the VSV for ACIS connector.

    5. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK VACUUM HOSES (INTAKE MANIFOLD - IACV, IACV - VSV FOR ACIS)
  1. Check that the vacuum hose is connected correctly.

  1. Check the vacuum hose for looseness and disconnection.

  1. Check the vacuum hose for cracks, holes and damage.



NG
REPAIR OR REPLACE VACUUM HOSES
OK


5. INSPECT INTAKE AIR CONTROL VALVE (INTAKE AIR SURGE TANK)

  1. A075984E02
    Check that the lever moves when a vacuum of 26.6 kPa (200 mmHg) is applied with the vacuum gauge on.

    OK:
    Lever moves

  1. Check that the vacuum of 26.6 kPa (200 mmHg) is sustained for 1 minute in the above state.

    OK:
    Vacuum is sustained



NG
REPLACE INTAKE AIR CONTROL VALVE (INTAKE AIR SURGE TANK) (Click here)
OK

REPLACE ECM (Click here)


← Starter Signal Circuit (from Aug 2012)Brake Override System (Nov 2010 – Jul 2011) →