2011-2016 FJ Cruiser · Service Manual ENGINE

Starter Signal Circuit

Circuit diagnosis · Vehicles built from Aug 2012

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

While the engine is being cranked, current flows from the ignition switch to terminal STA of the ECM as well as to the STA relay. For the automatic transmission model, current flows through the park/neutral position switch to the ECM.

WIRING DIAGRAM

A226862E01
A133424E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START position.

    OK:
    Switch Condition
    Starter Signal
    ON
    OFF
    Start
    ON

Result 
Result
Proceed to
Outside standard range
(for Manual Transmission Model)
A
Outside standard range
(for Automatic Transmission Model)
B
Within standard range
(for Manual Transmission Model)
C
Within standard range
(for Automatic Transmission Model)
D


B
Go to step 4

C
Go to step 3

D
Go to step 7
A


2. INSPECT IGNITION SWITCH
A203952E13
  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (AM1) - 1 (ST1)
    START position
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Ignition Switch)



NG
REPLACE IGNITION SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM - STA RELAY)
  1. Remove the STA relay.

  1. Disconnect the E81 ECM connector.

  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    STA relay terminal 1- E81-10 (STA)
    Always
    Below 1 Ω
    STA relay terminal 1- A1-1 (ST1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E81-10 (STA) or A1-1 (ST1) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 8
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

4. INSPECT PARK/NEUTRAL POSITION SWITCH
C193931E42
  1. Disconnect the B65 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 - 5
    Shift position P, N
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


5. INSPECT IGNITION SWITCH
A203952E13
  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (AM1) - 1 (ST1)
    START position
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Ignition Switch)



NG
REPLACE IGNITION SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the A1 ignition switch connector.

  1. Disconnect the B65 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A1-1 (ST1) - B65-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A1-1 (ST1) or B65-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - STA RELAY)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the E81 ECM connector.

  1. Disconnect the B65 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    STA relay terminal 1 - E81-10 (STA)
    Always
    Below 1 Ω
    STA relay terminal 1 - B65-5
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E81-10 (STA) or B65-5 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 8
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

8. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


9. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

REPAIR OR REPLACE STARTER CIRCUIT (STARTER - STA RELAY)


← Starter Signal Circuit (Nov 2010 – Jul 2012)ACIS Control Circuit (Jul 2007 – Jul 2009) →