2011-2016 FJ Cruiser · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic)
  1. (a) Ignition switch to ON
  2. (b) Brake pedal released
  3. (c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch
  4. ECM

WIRING DIAGRAM

A226161E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON when brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E22
  1. Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Stop Light Switch)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1 - VOLTAGE)
A226932E01
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch.

  1. Check the STP signal when the brake pedal is depressed and released.

    OK:
    Brake Pedal Operation
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E82-8 (ST1-) - B49-12 (E1)
    Brake pedal depressed
    0 to 3 V
    E82-8 (ST1-) - B49-12 (E1)
    Brake pedal released
    11 to 14 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A3-1 - E81-18 (STP)
    Always
    Below 1 Ω
    A3-4 - E82-8 (ST1-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A3-1 or E81-18 (STP) - Body ground
    Always
    10 kΩ or higher
    A3-4 or E82-8 (ST1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0504 Brake Switch "A" / "B" Correlation (Jul 2007 – Jul 2009)P0504 Brake Switch "A" / "B" Correlation (from Nov 2010) →