P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Nov 2010
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.- HINT:
- The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic)
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK OPERATION OF STOP LIGHT |
Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.
- OK:
- Stop lights turn ON when brake pedal is depressed.
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the stop light switch assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch pin not pushed
Below 1 Ω
Switch pin pushed
10 kΩ or higher
3 - 4
Switch pin not pushed
10 kΩ or higher
Switch pin pushed
Below 1 Ω
Text in Illustration *1
Component without harness connected
(Stop Light Switch)
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1 - VOLTAGE) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch.
Check the STP signal when the brake pedal is depressed and released.
- OK:
Brake Pedal Operation
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E82-8 (ST1-) - B49-12 (E1)
Brake pedal depressed
0 to 3 V
E82-8 (ST1-) - B49-12 (E1)
Brake pedal released
11 to 14 V
Text in Illustration *1
Rear view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM) |
Disconnect the stop light switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
A3-1 - E81-18 (STP)
Always
Below 1 Ω
A3-3 - E82-8 (ST1-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
A3-1 or E81-18 (STP) - Body ground
Always
10 kΩ or higher
A3-3 or E82-8 (ST1-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||


