2011-2016 FJ Cruiser · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.
Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Conditions
Trouble Areas
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic)
  1. (a) Ignition switch ON
  2. (b) Brake pedal released
  3. (c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch
  4. ECM

WIRING DIAGRAM

A133421E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON when brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT (Click here)
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
A072924E09
  1. Remove the stop light switch assembly.

  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Switch Positions
    Specified Conditions
    1 - 2
    Switch pin free
    Below 1 Ω
    3 - 4
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1- VOLTAGE)
G035663E04
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light SW.

  1. Check the STP signal when the brake pedal is depressed and released.

    OK:
    Brake Pedal Operations
    Specified Conditions
    Depressed
    STP signal ON
    Released
    STP signal OFF

  1. Measure the voltage between the terminals of the B3 and E47 ECM connectors.

    Standard Voltage:
    Tester Connections
    Brake Pedal Operations
    Specified Conditions
    ST1- (E47-16) - E1 (B3-1)
    Depressed
    Below 1.5 V
    Released
    7.5 to 14 V



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
A116299E03
  1. Disconnect the A3 stop light switch connector.

  1. Disconnect the E47 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    Stop light switch (A3-1) - STP (E47-15)
    Below 1 Ω
    Stop light switch (A3-4) - ST1- (E47-16)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    Stop light switch (A3-1) or STP (E47-15) - Body ground
    10 kΩ or higher
    Stop light switch (A3-4) or ST1- (E47-16) - Body ground

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0500 Vehicle Speed Sensor "A" (from Nov 2010)P0504 Brake Switch "A" / "B" Correlation (Aug 2009 – Oct 2010) →