2011-2016 FJ Cruiser · Service Manual ENGINE

P0300 Random / Multiple Cylinder Misfire Detected

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014

DESCRIPTION

A093767E12
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the VVT sensor and the Crankshaft Position (CKP) sensor. The VVT sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and stores a DTC when either one of the following conditions, which could cause Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
  1. At a high engine rpm, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
  2. At a normal engine rpm, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.


WIRING DIAGRAM

A226863E01
A226860E01

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the tester on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Using the tester, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder (cylinder No. 1 to No. 6) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle several times with the conditions, such as engine rpm and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.
    Engine RPM
    Duration
    Idling
    6 minutes or more
    1000
    4 minutes or more
    2000
    2 minutes or more
    3000
    1.5 minute or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 5 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors may be a cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
  5. After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5 and No. 6).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine RPM. If misfires only occur during high engine RPM driving, only DTC P0300 is stored.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the intelligent tester.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  8. When either Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
  9. When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be detected.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 is output
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3. READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4. READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6.

  1. Allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to #6 displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Move the shift lever to D.

    2. Check Cylinder #1 Misfire Count to #6.

    3. If misfire counts are still not displayed, perform procedure "A" and "B", and then check the misfire counts again.Procedure A: Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using the tester (Misfire RPM and Misfire Load)" procedures above.Procedure B: Read Cylinder #1 Misfire Count to #6 or DTCs displayed on the tester.

      Result 
      Result
      Proceed to
      Most misfires occur in only 1 or 2 cylinders
      A
      3 cylinders or more have equal misfire counts
      B

      HINT:
      1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
      2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
      3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 16
A


Go to step 7

5. INSPECT SPARK PLUG
  1. Inspect the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


Go to step 8

6. CHECK FOR SPARKS AND IGNITION
  1. Check for the spark and ignition (Click here).



NG
Go to step 27
OK


Go to step 9

7. CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


Go to step 10

8. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND/OR #60 VOLTAGE)
A226857E01
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B50-6 (#10) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-1 (#20) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-7 (#30) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-2 (#40) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-8 (#50) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-3 (#60) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


Go to step 11

9. CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


Go to step 12

10. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
Go to step 29
OK


Go to step 13

11. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    Between 80°C and 97°C (176°F and 207°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Between 80°C and 97°C (176°F and 207°F)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or higher.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


Go to step 14

12. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


Go to step 15

13. CHECK VALVE TIMING
A135015E06
  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    Text in Illustration:
    *1
    Alignment Mark

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


Go to step 16

14. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


Go to step 17

15. CHECK WHETHER DTC OUTPUT RECURS (DTC P0300,P0301,P0302,P0303,P0304,P0305 OR P0306)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.

  1. Check the DTC judgment result.

    Result 
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit


NEXT

END

16. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
Go to step 29
OK


Go to step 19

17. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    Between 80°C and 97°C (176°F and 207°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Between 80°C and 97°C (176°F and 207°F)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or higher.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


Go to step 20

18. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter sub-assembly (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


Go to step 21

19. CHECK VALVE TIMING
A135015E06
  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    Text in Illustration:
    *1
    Alignment Mark

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


Go to step 22

20. INSPECT SPARK PLUG
  1. Inspect the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


Go to step 23

21. CHECK FOR SPARKS AND IGNITION
  1. Check for the sparks and ignition (Click here).



NG
Go to step 27
OK


Go to step 24

22. CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


Go to step 25

23. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND/OR #60 VOLTAGE)
A226857E01
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B50-6 (#10) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-1 (#20) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-7 (#30) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-2 (#40) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-8 (#50) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V
    B50-3 (#60) - B50-14 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


Go to step 26

24. CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


Go to step 27

25. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


Go to step 28

26. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.

  1. Check the DTC judgment result.

    Result 
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit


NEXT

END

27. CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the fuel injector connectors.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 28
OK

REPLACE SPARK PLUG (Click here)

28. CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the ignition coil to an ignition coil that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the fuel injector connectors.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL (Click here)

29. CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (Dec 2007 – Jul 2009)P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (Nov 2010 – Oct 2012) →