P0300 Random / Multiple Cylinder Misfire Detected
Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009
Also covers:
- P0301 Cylinder 1 Misfire Detected
- P0302 Cylinder 2 Misfire Detected
- P0303 Cylinder 3 Misfire Detected
- P0304 Cylinder 4 Misfire Detected
- P0305 Cylinder 5 Misfire Detected
- P0306 Cylinder 6 Misfire Detected
Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014
DESCRIPTION


When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. High HC concentration levels can cause increase in exhaust emission levels. Extremely high concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the Crankshaft Position (CKP) sensor. The VVT sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, the ECM illuminates the MIL and stores a DTC.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0300 |
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 P0305 P0306 |
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
|
MONITOR DESCRIPTION
-
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).- Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.
- An excessive misfiring rate (approximately 500 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
- A catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.
- Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.
WIRING DIAGRAM
Wiring diagram of the ignition system.



CONFIRMATION DRIVING PATTERN
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester ON.
- Record the DTC(s) and freeze frame data.
- Using the tester, switch the ECM from normal mode to check mode (Click here).
- Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to Cylinder #6 Misfire Count) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
- Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.
- HINT:
- In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.
- In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.
Engine RPM
Duration
Idling
3.5 minutes or more
1000
3 minutes or more
2000
1.5 minutes or more
3000
1 minute or more
- Check whether misfires have occurred by checking DTCs and freeze frame data.
- HINT:
- Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.
- Record the DTC(s), freeze frame data and misfire counts.
- Turn the ignition switch off and wait for at least 5 seconds.
INSPECTION PROCEDURE
- HINT:
- If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
- Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
- If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
- There was insufficient fuel volume in the tank.
- Improper fuel is used.
- The spark plugs have been contaminated.
- After finishing repairs, check the misfire counts of the cylinders ( [Cylinder #1 Misfire Count to Cylinder #6 Misfire Count]).
- Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
- For 6 and 8 cylinder engines, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine RPM. If misfires occur only in high engine RPM areas, only DTC P0300 is stored.
In the event of DTC P0300 being present, perform the following operations:
- Clear the DTC (Click here).
- Start the engine and conduct the confirmation driving pattern.
- Read the misfiring rates of each cylinder or DTC(s) using the tester.
- Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
- After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
- When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be Rich (-20% or less) or Lean (+20% or more).
- When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire have occurred only while warming up the engine.
- An extremely imbalanced drive wheel which cause body vibration may cause misfire DTCs detection.
- If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
- HINT:
- Write down the DTCs.
Result Result
Proceed to
P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306
A
P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs
B
- HINT:
- If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
- HINT:
- The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
| NEXT | |
| 3. CHECK PCV HOSE CONNECTIONS |
- OK:
- PCV hose is correctly connected and is not damaged.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (CYLINDER MISFIRE COUNT) |
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6
Read each value for Cylinder #1 Misfire Count to #6 displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:
Start the engine and let it idle.
Move the shift lever to D.
Check the Cylinder #1 Misfire Count to #6.
If misfire counts are still not displayed, perform steps (c) and (d).
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedures above.
Read the Cylinder #1 Misfire Count to #6 or DTCs displayed on the tester.
| Result |
Proceed to |
| Most misfires occur in only 1 or 2 cylinders |
A |
| 3 cylinders or more have equal misfire counts |
B |
- HINT:
- If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
- If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
- If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.
- If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
|
|
||||
| A | |
| 5. INSPECT SPARK PLUG |
![]() ![]() |
Remove the ignition coil and the spark plug of the misfiring cylinder.
Measure the spark plug electrode gap.
- Maximum gap:
- 1.0 to 1.1 mm (0.039 to 0.043 in.)
Check the electrode for carbon deposits.
Recommended Spark Plug Manufacturer
Product
DENSO
K20HR-U11
NGK
LFR60C11
- NOTICE:
- If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.
Reinstall the ignition coil and the spark plug.
|
|
||||
| OK | |
| 6. CHECK FOR SPARKS AND IGNITION |
Disconnect the fuel injector connectors to prevent the engine from starting.
- CAUTION:
- Always disconnect all fuel injector connectors.
- NOTICE:
- Do not crank the engine for more than 2 seconds.
Remove the ignition coil from the cylinder head.
Install the spark plug onto the ignition coil.
Attach the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check the spark.
- OK:
- Sparks jump across electrode gap.
Install the ignition coil.
Reconnect the fuel injector connectors.
|
|
||||
| OK | |
| 7. CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder (Click here).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR) |
![]() ![]() |
Disconnect the fuel injector connector (of the misfiring cylinder).
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Cylinder
Tester Connection
Switch Condition
Specified Condition
No. 1
B11-2 - Body ground
Ignition switch ON
11 to 14 V
No. 2
B25-2 - Body ground
Ignition switch ON
11 to 14 V
No. 3
B10-2-1 - Body ground
Ignition switch ON
11 to 14 V
No. 4
B21-2 - Body ground
Ignition switch ON
11 to 14 V
No. 5
B9-2-1 - Body ground
Ignition switch ON
11 to 14 V
No. 6
B18-2 - Body ground
Ignition switch ON
11 to 14 V
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Cylinder
Tester Connection
Condition
Specified Condition
No. 1
B11-1 - Body ground
Always
10 kΩ or higher
B11-1 - B3-2 (#10)
Always
Below 1 Ω
No. 2
B25-1 - Body ground
Always
10 kΩ or higher
B25-1 - B3-3 (#20)
Always
Below 1 Ω
No. 3
B10-1 - Body ground
Always
10 kΩ or higher
B10-1 - B3-4 (#30)
Always
Below 1 Ω
No. 4
B21-1 - Body ground
Always
10 kΩ or higher
B21-1 - B3-5 (#40)
Always
Below 1 Ω
No. 5
B9-1 - Body ground
Always
10 kΩ or higher
B9-1 - B3-6 (#50)
Always
Below 1 Ω
No. 6
B18-1 - Body ground
Always
10 kΩ or higher
B18-1 - B3-7 (#60)
Always
Below 1 Ω
|
|
||||
| OK | |
| 9. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE) |
![]() ![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B3-2(#10) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-3(#20) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-4(#30) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-5(#40) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-6(#50) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-7(#60) - B1-7(E01)
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 10. CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
|
||||
| OK | |
| 11. CHECK VALVE CLEARANCE OF MISFIRING CYLINDER |
Check the valve clearance (Click here).
|
|
||||
| OK | |
| 12. CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leak.
- OK:
- No leak from air induction system.
|
|
||||
| OK | |
| 13. CHECK VALVE TIMING |
Remove the cylinder head cover (Click here or Click here).

Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
- OK:
- Timing marks on camshaft timing gears are aligned as shown in the illustration.
Reinstall the cylinder head cover (Click here or Click here).
|
|
||||
| OK | |
| 14. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 15. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
- Standard:
- With cold engine: Same as ambient air temperature.
With warm engine: 80°C to 100°C (176°C to 212°F).
|
|
||||
| OK | |
| 16. INSPECT MASS AIR FLOW METER |
Read the values using the intelligent tester (MAF).
- NOTICE:
- Turn the ignition switch off.
- Perform the inspection with the vehicle indoors and on a level surface.
- Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
- During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.
- Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Wait for 30 seconds, and read the values on the tester.
- Standard value:
- Less than 0.92 g/sec
Inspect the mass air flow meter.
Remove the mass air flow meter (Click here).
Using a work light, check that the platinum filament (heater portion) in the mass air flow meter has no foreign matter attached.

- OK:
- No foreign matter attached
Reinstall the mass air flow meter (Click here).
|
|
||||
| OK | ||
| ||
| 17. CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leak.
- OK:
- No leak from air induction system.
|
|
||||
| OK | |
| 18. CHECK VALVE TIMING |
Remove the cylinder head cover (Click here or Click here).

Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
- OK:
- Timing marks on camshaft timing gears are aligned as shown in the illustration.
Reinstall the cylinder head cover (Click here or Click here).
|
|
||||
| OK | |
| 19. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 20. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
- Standard:
- With cold engine: Same as ambient air temperature.
With warm engine: 80°C to 100°C (176°C to 212°F).
|
|
||||
| OK | |
| 21. INSPECT MASS AIR FLOW METER |
Read the values using the intelligent tester (MAF).
- NOTICE:
- Turn the ignition switch off.
- Perform the inspection with the vehicle indoors and on a level surface.
- Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
- During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.
- Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Wait for 30 seconds, and read the values on the tester.
- Standard value:
- Less than 0.92 g/sec
Inspect the mass air flow meter.
Remove the mass air flow meter (Click here).
Using a work light, check that the platinum filament (heater portion) in the mass air flow meter has no foreign matter attached.

- OK:
- No foreign matter attached
Reinstall the mass air flow meter (Click here).
|
|
||||
| OK | |
| 22. INSPECT SPARK PLUG |
![]() ![]() |
Remove the ignition coil and the spark plug of the misfiring cylinder.
Measure the spark plug electrode gap.
- Maximum gap:
- 1.0 to 1.1 mm (0.039 to 0.043 in.)
Check the electrode for carbon deposits.
Recommended Spark Plug Manufacturer
Product
DENSO
K20HR-U11
NGK
LFR6C11
- NOTICE:
- If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.
Reinstall the ignition coil and the spark plug.
|
|
||||
| OK | |
| 23. CHECK FOR SPARKS AND IGNITION |
Disconnect the fuel injector connectors to prevent the engine from starting.
- CAUTION:
- Always disconnect all fuel injector connectors.
- NOTICE:
- Do not crank the engine for more than 2 seconds.
Remove the ignition coil from the cylinder head.
Install the spark plug onto the ignition coil.
Attach the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check the spark.
- OK:
- Sparks jump across electrode gap.
Install the ignition coil.
Reconnect the fuel injector connectors.
|
|
||||
| OK | |
| 24. CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder (Click here).
|
|
||||
| OK | |
| 25. CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR) |
![]() ![]() |
Disconnect the fuel injector connector (of the misfiring cylinder).
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Cylinder
Tester Connection
Switch Condition
Specified Condition
No. 1
B11-2 - Body ground
Ignition switch ON
11 to 14 V
No. 2
B25-2 - Body ground
Ignition switch ON
11 to 14 V
No. 3
B10-2-1 - Body ground
Ignition switch ON
11 to 14 V
No. 4
B21-2 - Body ground
Ignition switch ON
11 to 14 V
No. 5
B9-2-1 - Body ground
Ignition switch ON
11 to 14 V
No. 6
B18-2 - Body ground
Ignition switch ON
11 to 14 V
Turn the ignition switch off
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Cylinder
Tester Connection
Condition
Specified Condition
No. 1
B11-1 - Body ground
Always
10 kΩ or higher
B11-1 - B3-2 (#10)
Always
Below 1 Ω
No. 2
B25-1 - Body ground
Always
10 kΩ or higher
B25-1 - B3-3 (#20)
Always
Below 1 Ω
No. 3
B10-1 - Body ground
Always
10 kΩ or higher
B10-1 - B3-4 (#30)
Always
Below 1 Ω
No. 4
B21-1 - Body ground
Always
10 kΩ or higher
B21-1 - B3-5 (#40)
Always
Below 1 Ω
No. 5
B9-1 - Body ground
Always
10 kΩ or higher
B9-1 - B3-6 (#50)
Always
Below 1 Ω
No. 6
B18-1 - Body ground
Always
10 kΩ or higher
B18-1 - B3-7 (#60)
Always
Below 1 Ω
|
|
||||
| OK | |
| 26. INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE) |
![]() ![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B3-2(#10) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-3(#20) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-4(#30) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-5(#40) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-6(#50) - B1-7(E01)
Ignition switch ON
11 to 14 V
B3-7(#60) - B1-7(E01)
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 27. CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
|
||||
| OK | |
| 28. CHECK VALVE CLEARANCE OF MISFIRING CYLINDER |
Check the valve clearance (Click here).
|
|
||||
| OK | ||
| ||
| 29. CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed spark plug to a spark plug that functions normally.
Perform a spark test.
- CAUTION:
- Always disconnect all fuel injector connectors.
- NOTICE:
- Do not crank the engine for more than 2 seconds.
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the fuel injector connector.
Ground the spark plug.
Check if sparks occur while the engine is being cranked.
- OK:
- Sparks jump across electrode gap.
|
|
||||
| OK | ||
| ||
| 30. CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed ignition coil to a ignition coil that functions normally.
Perform a spark test.
- CAUTION:
- Always disconnect all fuel injector connectors.
- NOTICE:
- Do not crank the engine for more than 2 seconds.
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the fuel injector connector.
Ground the spark plug.
Check if sparks occur while the engine is being cranked.
- OK:
- Sparks jump across electrode gap.
|
|
||||
| OK | ||
| ||



