C1434 Steering Angle Sensor Output Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2012
Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012
DESCRIPTION
Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1434 |
An error in communication between the skid control ECU and the steering angle sensor, or an abnormal steering angle sensor zero point. |
|
WIRING DIAGRAM
Refer to DTC C1432 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1434, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (Click here).
- When any of the speed sensors or the yaw rate and deceleration sensor has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensors or yaw rate and deceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and deceleration sensor first, and then inspect and repair the steering angle sensor.
- When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1434, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (Click here).
| 1. CHECK DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) and turn the steering wheel to the right and left, and then check that no speed sensor or yaw rate and deceleration sensor DTCs are output (Click here).
Result Result
Proceed to
No CAN communication system, speed sensor, or yaw rate and deceleration sensor DTCs are output
A
CAN communication system DTC is output
B
Speed sensor or yaw rate and deceleration sensor DTC is output
C
- HINT:
- If there is a malfunction in any of the speed sensors or the yaw rate and deceleration sensor, an abnormal value may be output although the steering angle sensor is normal.
- If speed sensor and yaw rate and deceleration sensor DTCs are output simultaneously, repair these two sensors first, and then inspect the steering angle sensor.
- If there is a malfunction in any of the speed sensors or the yaw rate and deceleration sensor, an abnormal value may be output although the steering angle sensor is normal.
|
|
||||
|
|
||||
| A | |
| 2. INSPECT STEERING ANGLE SENSOR (IG, BAT TERMINAL) |
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the E16 steering angle sensor connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E16-1 (IG) - Body ground
Ignition switch ON
11 to 14 V
E16-9 (BAT) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Steering Angle Sensor)
|
|
||||
| OK | |
| 3. INSPECT STEERING ANGLE SENSOR (GND TERMINAL) |
Turn the ignition switch off.
Disconnect the E16 steering angle sensor connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
E16-2 (ESS) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Steering Angle Sensor)
|
|
||||
| OK | ||
| ||
