2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012


BUS CHECK (COMMUNICATION MALFUNCTION ECU)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.

  1. C128170
    Select "Bus Check" from the "System Select" screen on the intelligent tester.

  2. C128171
    Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

  3. C128172
    Select the system of the DTC to be checked and select "Details".

  4. C128173
    CAN communication system DTCs are displayed.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.

  1. C128171
    Select "Communication Bus Check" from the "Bus Check" screen.

  2. C197126
    The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    1. If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).

    2. C197127
      The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop down list. The drop down list displays "ALL", "V Bus", and the names of the remaining buses.
      Combo Box
      Display Content
      ALL
      All ECUs (sensors) connected to the CAN bus
      V Bus
      ECUs (sensors) connected to the V bus
      Bus Name
      ECUs (sensors) connected to the selected bus
    3. The connection status (shown below) is indicated by the background color displayed behind the system name.
      ECU (Sensor) on V Bus
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Red
      Has never been detected but has connection history
      Not displayed
      Has never been detected and has no connection history

  3. C128179
    "There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
  1. Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.

    ECU/Sensor Name
    Intelligent Tester Display
    Check Method
    Airbag Sensor Assembly
    Airbag
    Installed on all vehicles
    Combination Meter ECU
    Combination Meter
    Installed on all vehicles
    ECM
    ECM (Engine)
    Installed on all vehicles
    Skid Control ECU
    Skid Control (ABS/VSC/TRAC)
    Installed on all vehicles
    Steering Angle Sensor
    Spiral Cable (Steering Angle Sensor)
    Installed on all vehicles
    Yaw Rate Sensor
    Yaw Rate / Deceleration Sensor
    Installed on all vehicles
    Driving Support Switch Control ECU
    D-SEAT SW
    w/ CRAWL


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the intelligent tester.
  2. If CAN communication system DTCs are output, trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How To Proceed with Troubleshooting" (Click here).

  1. SKID CONTROL ECU

    HINT:
    DTC communication uses the SIL Line.

    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus OFF
    U0100
    Lost Communication with ECM / PCM "A"
    U0126
    Lost Communication with Steering Angle Sensor Module
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Lost Communication with Lateral Acceleration Sensor Module

  2. COMBINATION METER ECU

    HINT:
    DTC communication uses the CAN communication system.

    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM / PCM "A"
    U0129
    Lost Communication with Skid Control ECU
    U0151
    Lost Communication with Airbag ECU

  3. YAW RATE SENSOR

    HINT:
    1. The yaw rate sensor is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Yaw Rate/Deceleration Sensor" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Yaw Rate Sensor Communication Stop Mode" (Click here).

  4. STEERING ANGLE SENSOR

    HINT:
    1. The steering sensor is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Spiral cable (Steering Angle Sensor)" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Steering Angle Sensor Communication Stop Mode" (Click here).

  5. ECM

    HINT:
    1. The ECM is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "ECM (Engine)" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "ECM Communication Stop Mode" (Click here).

  6. AIRBAG SENSOR ASSEMBLY

    HINT:
    1. The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Airbag " is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Center Airbag Sensor Communication Stop Mode" (Click here).

  7. DRIVING SUPPORT SWITCH CONTROL ECU (w/ CRAWL)

    HINT:
    1. The driving support switch control ECU is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "D-SEAT SW" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Driving Support Switch Control ECU Communication Stop Mode" (Click here).


DTC COMBINATION TABLE
Output from
Output DTC
Detected Communication Stop Mode
V-Bus
ECM Communication Stop Mode
Skid Control ECU Communication Stop Mode
Yaw Rate Sensor Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Combination Meter ECU Communication Stop Mode
Driving Support Switch Control ECU Communication Stop Mode*2
Skid Control ECU
U0073
X
○*1
○
○
X
X
X
U0100
○
○*1
X
X
X
X
X
U0126
X
○*1
X
○
X
X
X
U0123
X
○*1
○
X
X
X
X
U0124
X
○*1
○
X
X
X
X
Combination Meter ECU
U0100
○
X
X
X
X
○*1
X
U0129
X
○
X
X
X
○*1
X
U0151
X
X
X
X
○
○*1
X

HINT:
  1. ○:Stored.
  2. X: When one side of branch wire is open, storage may occur.
  3. *1: DTC may not be output when the CAN communication system malfunctions.
  4. *2: w/ CRAWL

  1. Perform troubleshooting according to the combination of DTCs output.

    HINT:
    1. Skid Control ECU Communication Stop Mode: (Click here)
    2. ECM Communication Stop Mode: (Click here)
    3. Yaw Rate Sensor Communication Stop Mode: (Click here)
    4. Steering Angle Sensor Communication Stop Mode: (Click here)
    5. Combination Meter ECU Communication Stop Mode: (Click here)
    6. Center Airbag Sensor Communication Stop Mode: (Click here)
    7. Driving Support Switch Control ECU Communication Stop Mode (w/ CRAWL): (Click here)

← DIAGNOSIS SYSTEM (Aug 2011 – Jul 2012)FAIL-SAFE CHART (Jul 2007 – Oct 2010) →