2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Only Wireless Control Function is Inoperative

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher assembly (hazard warning lights).

WIRING DIAGRAM

B267296E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the power window regulator master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK KEY REMINDER WARNING SYSTEM
  1. Check that the key reminder warning buzzer operates normally.

    OK:
    Key reminder warning buzzer operates normally.



NG
GO TO KEY REMINDER WARNING SYSTEM (Click here)
OK


3. CHECK DOOR CONTROL TRANSMITTER
  1. When another registered door control transmitter is used, check that the wireless door lock function operates normally.

    OK:
    Wireless door control functions operate normally.



NG
Go to step 6
OK


4. CHECK TRANSMITTER LED ILLUMINATION
  1. Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

    Result 
    Result
    Proceed to
    Transmitter LED does not illuminate when switch is pressed and held
    A
    Transmitter LED illuminates 3 times or more when switch is pressed and held
    B
    Transmitter LED illuminates once or twice but not third time
    C

    HINT:
    If the transmitter LED illuminates once or twice but not three times, the transmitter battery may be depleted.



B
REPLACE DOOR CONTROL TRANSMITTER (Click here)

C
REPLACE TRANSMITTER BATTERY (Click here)
A


5. CHECK TRANSMITTER BATTERY

  1. E114749E03
    Remove the battery from the door control transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.)) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (Click here).

    NOTICE:
    Do not wrap the lead wire around the terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    Text in Illustration 
    *1
    Lead Wire

  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

  1. B265553
    Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Battery positive (+) - Battery negative (-)
    Press one of the transmitter switches
    2.2 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER (Click here)

6. CHECK WAVE ENVIRONMENT
  1. Bring the transmitter near the door control receiver, and perform a wireless operation check.

    HINT:
    1. When the transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Wireless functions operate normally.



NG
Go to step 7
OK

AFFECTED BY WAVE INTERFERENCE

7. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Wireless Door Lock Buzzer
    A
    w/o Wireless Door Lock Buzzer
    B



B
Go to step 12
A


8. SWITCH TO SELF-DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Make sure that the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds after removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.

    3. Within 30 seconds after turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and then off.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.

  1. B220865E21
    Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer sound.


NEXT


9. CHECK SELF-DIAGNOSTIC MODE
B163380E57
  1. Check the diagnostic outputs when the door control transmitter switch is held down. The diagnostic outputs can be checked by the wireless door lock buzzer sound.

    Result 
    Result
    Proceed to
    Normal waves (wireless door lock buzzer patterns) for LOCK and UNLOCK switches are output
    A
    Unmatching recognition code is output
    B
    No diagnosis outputs
    C



B
Go to step 10

C
Go to step 11
A

REPLACE MAIN BODY ECU

10. REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).

    OK:
    Recognition code can be registered.



NG
Go to step 15
OK

END

11. CHECK DOOR CONTROL RECEIVER (RESPONSE)
  1. Prepare the door control transmitter from another vehicle.

  1. Press and hold down the door control transmitter switch.

  1. Check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



NG
Go to step 12
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE (Click here)

12. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

  1. B267859E01
    Disconnect the E23 door control receiver connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E23-5 (+B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E23-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)

  1. Reconnect the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CHECK DOOR CONTROL RECEIVER (OUTPUT)

  1. B238267E06
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E23-2 (RDA) - Body ground
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control Receiver)



NG
REPLACE DOOR CONTROL RECEIVER
OK


14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
  1. Disconnect the E7 main body ECU connector.

  1. Disconnect the E23 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-4 (RDA) - E23-2 (RDA)
    Always
    Below 1 Ω
    E7-3 (PRG) - E23-3 (PRG)
    Always
    Below 1 Ω
    E7-4 (RDA) - Body ground
    Always
    10 kΩ or higher
    E7-3 (PRG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the door control receiver connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door control receiver with a new or known good one.


NEXT


16. REGISTER RECOGNITION CODE
  1. Perform the Registration procedure (Click here).


NEXT


17. CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked using transmitter.



NG
REPLACE MAIN BODY ECU
OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)


← Only Wireless Control Function is Inoperative (Jul 2007 – Oct 2010)No Answer-Back (Jul 2007 – Oct 2010) →