2011-2016 FJ Cruiser · Service Manual ENGINE

P0351 Ignition Coil "A" Primary / Secondary Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check No. 1 ignition coil assembly.
  3. If DTC P0352 is set, check No. 2 ignition coil assembly.
  4. If DTC P0353 is set, check No. 3 ignition coil assembly.
  5. If DTC P0354 is set, check No. 4 ignition coil assembly.
  6. If DTC P0355 is set, check No. 5 ignition coil assembly.
  7. If DTC P0356 is set, check No. 6 ignition coil assembly.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.
A122501E02
DTC No.
DTC Detection Conditions
Trouble Areas
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine running (1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil and ECM
  3. No. 1 to No. 6 ignition coils
  4. ECM

  1. A112406E01
  2. Reference: Inspection using an oscilloscope
    While cranking or idling, check the waveform between terminals IGT(1 to 6) and E1, and IGF1 and E1 of the ECM connector.
    Items
    Contents
    Terminals
    CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
    CH2: IGF1 - E1
    Equipment Settings
    2 V/DIV, 20 msec./DIV
    Conditions
    Cranking or idling

MONITOR DESCRIPTION

A115898E07
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 1 second after the engine is next started.

WIRING DIAGRAM

A174420E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK SPARK PLUG AND SPARK OF MISFIRING CYLINDER
  1. Check the spark plug and sparks of the misfiring cylinder (Click here).



NG
Go to step 4
OK


2. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
A116293E07
  1. Disconnect the B5, B6, B7, B20, B23 or B24 ignition coil connector.

  1. Disconnect the B1 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGF (B7-2) - IGF1 (B1-24)
    Below 1 Ω
    IGF (B24-2) - IGF1 (B1-24)
    IGF (B6-2) - IGF1 (B1-24)
    IGF (B23-2) - IGF1 (B1-24)
    IGF (B5-2) - IGF1 (B1-24)
    IGF (B20-2) - IGF1 (B1-24)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGF (B7-2) or IGF1 (B1-24) - Body ground
    10 kΩ or higher
    IGF (B24-2) or IGF1 (B1-24) - Body ground
    IGF (B6-2) or IGF1 (B1-24) - Body ground
    IGF (B23-2) or IGF1 (B1-24) - Body ground
    IGF (B5-2) or IGF1 (B1-24) - Body ground
    IGF (B20-2) or IGF1 (B1-24) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (IGF1 VOLTAGE)
A115970E11
  1. Disconnect the ignition coil connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the B1 and B3 ECM connectors.

    Standard Voltage:
    Tester Connection
    Specified Condition
    IGF1 (B1-24) - E1 (B3-1)
    4.5 to 5.5 V

  1. Reconnect the ignition coil connector.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
A116293E08
  1. Disconnect the B5, B6, B7, B20, B23 or B24 ignition coil connector.

  1. Disconnect the B1 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGT1 (B7-3) - IGT1 (B1-8)
    Below 1 Ω
    IGT2 (B24-3) - IGT2 (B1-9)
    IGT3 (B6-3) - IGT3 (B1-10)
    IGT4 (B23-3) - IGT4 (B1-11)
    IGT5 (B5-3) - IGT5 (B1-12)
    IGT6 (B20-3) - IGT6 (B1-13)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGT1 (B7-3) or IGT1 (B1-8) - Body ground
    10 kΩ or higher
    IGT2 (B24-3) or IGT2 (B1-9) - Body ground
    IGT3 (B6-3) or IGT3 (B1-10) - Body ground
    IGT4 (B23-3) or IGT4 (B1-11) - Body ground
    IGT5 (B5-3) or IGT5 (B1-12) - Body ground
    IGT6 (B20-3) or IGT6 (B1-13) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5, OR IGT6 VOLTAGE)
A115970E12
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the B1 and B3 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGT1 (B1-8) - E1 (B3-1)
    0.1 to 4.5 V
    IGT2 (B1-9) - E1 (B3-1)
    IGT3 (B1-10) - E1 (B3-1)
    IGT4 (B1-11) - E1 (B3-1)
    IGT5 (B1-12) - E1 (B3-1)
    IGT6 (B1-13) - E1 (B3-1)



NG
REPLACE ECM (Click here)
OK


6. INSPECT ECM (IGT1, IGT2, IGT3, IGT4, IGT5, OR IGT6 VOLTAGE)
A116294E03
  1. Disconnect the B5, B6, B7, B20, B23 or B24 ignition coil connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the B1 and B3 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGT1 (B1-8) - E1 (B3-1)
    4.5 V or more
    IGT2 (B1-9) - E1 (B3-1)
    IGT3 (B1-10) - E1 (B3-1)
    IGT4 (B1-11) - E1 (B3-1)
    IGT5 (B1-12) - E1 (B3-1)
    IGT6 (B1-13) - E1 (B3-1)

  1. Reconnect the ignition coil connector.



NG
Go to step 8
OK


7. INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A115969E09
  1. Disconnect the B5, B6, B7, B20, B23 or B24 ignition coil connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    GND (B7-4) - Body ground
    Below 1 Ω
    GND (B24-4) - Body ground
    GND (B6-4) - Body ground
    GND (B23-4) - Body ground
    GND (B5-4) - Body ground
    GND (B20-4) - Body ground

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the wire harness side connector.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (B7-1) - GND (B7-4)
    11 to 14 V
    +B (B24-1) - GND (B24-4)
    +B (B6-1) - GND (B6-4)
    +B (B23-1) - GND (B23-4)
    +B (B5-1) - GND (B5-4)
    +B (B20-1) - GND (B20-4)

  1. Reconnect the ignition coil connector.



OK
REPLACE IGNITION COIL ASSEMBLY (Click here)
NG


8. CHECK HARNESS AND CONNECTOR (IGNITION COIL - IGNITION SWITCH)

  1. A116295E05
    Disconnect the B5, B6, B7, B20, B23 or B24 ignition coil connector.

  1. Disconnect the A1 ignition switch connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (B7-1) - IG2 (A1-6)
    Below 1 Ω
    +B (B24-1) - IG2 (A1-6)
    +B (B6-1) - IG2 (A1-6)
    +B (B23-1) - IG2 (A1-6)
    +B (B5-1) - IG2 (A1-6)
    +B (B20-1) - IG2 (A1-6)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (B7-1) or IG2 (A1-6) - Body ground
    10 kΩ or higher
    +B (B24-1) or IG2 (A1-6) - Body ground
    +B (B6-1) or IG2 (A1-6) - Body ground
    +B (B23-1) or IG2 (A1-6) - Body ground
    +B (B5-1) or IG2 (A1-6) - Body ground
    +B (B20-1) or IG2 (A1-6) - Body ground

  1. Reconnect the ignition coil connector.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (from Aug 2009)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (Aug 2009 – Jul 2014) →