2011-2016 FJ Cruiser · Service Manual ENGINE

P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magneto Resistance Element).
The VVT intake camshaft drive gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affect the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each engine revolution. Based on the combination of the G signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
DTC No.
DTC Detection Condition
Trouble Area
P0340
Either of following conditions is met:
  1. No VVT sensor signal to ECM while cranking. (2 trip detection logic)
  2. Missing VVT sensor signal despite crankshaft position sensor signal input normal at engine speed of 600 rpm or more. (1 trip detection logic)
  1. Open or short in VVT sensor circuit (for intake side)
  2. VVT sensor (for intake side)
  3. Camshaft timing pulley (for intake side)
  4. Jumped tooth of timing chain
  5. ECM
P0345
No VVT sensor signal to ECM at engine speed 600 rpm or more. (1 trip detection logic)
P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)

  1. A122767E04
  2. Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. INSPECT ECM TERMINAL VOLTAGE
A226928E01
  1. Inspect the ECM using an oscilloscope.

    1. While the engine is idling, check the waveform between the terminals of the ECM connector.

      Standard:
      Tester Connection
      Tool Setting
      Condition
      Specified Condition
      B47-9 (VV1+) - B47-10 (VV1-)
      5 V/DIV., 20 msec./DIV.
      Idling
      Correct waveform as shown in illustration
      B47-12 (VV2+) - B47-11 (VV2-)
      5 V/DIV., 20 msec./DIV.
      Idling
      Correct waveform as shown in illustration
      B47-6 (NE+) - B47-5 (NE-)
      5 V/DIV., 20 msec./DIV.
      Idling
      Correct waveform as shown in illustration

      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to ECM)
      *2
      VV1, VV2 and NE Signal Waveforms



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. CHECK VVT SENSOR (SENSOR POWER SOURCE)
A193258E02
  1. Disconnect the VVT sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B63-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V
    B64-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to VVT Sensor)
    *2
    for bank 1
    *3
    for bank 2



NG
Go to step 10
OK


3. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B63-1 (VVR+) - B47-9 (VV1+)
    Always
    Below 1 Ω
    B64-1 (VVL+) - B47-12 (VV2+)
    Always
    Below 1 Ω
    B63-2 (VVR-) - B47-10 (VV1-)
    Always
    Below 1 Ω
    B64-2 (VVL-) - B47-11 (VV2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B63-1 (VVR+) or B47-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B64-1 (VVL+) or B47-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B63-2 (VVR-) or B47-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B64-2 (VVL-) or B47-11 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK SENSOR INSTALLATION (VVT SENSOR)
BR03795E32
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
TIGHTEN SENSOR (Click here)
OK


5. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


6. REPLACE VVT SENSOR (FOR INTAKE SIDE)
  1. Replace the VVT sensor (for intake side) (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0340,P0342,P0343,P0345,P0347 OR P0348)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode (Click here).

  1. Start the engine and allow the engine to idle for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0340,P0342,P0343,P0345,P0347 or P0348 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A


8. CHECK VALVE TIMING
A135015E06
  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    Text in Illustration:
    *1
    Alignment Mark

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


9. CHECK WHETHER DTC OUTPUT RECURS (DTC P0340,P0342,P0343,P0345,P0347 OR P0348)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode (Click here).

  1. Start the engine and allow the engine to idle for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0340,P0342,P0343,P0345,P0347 or P0348 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END

10. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor (for intake camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B63-3 (VC) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B64-3 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B63-3 (VC) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B64-3 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (Jul 2007 – Jul 2009)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (Jul 2007 – Jul 2009) →