2011-2016 FJ Cruiser · Service Manual ENGINE

P0500 Vehicle Speed Sensor "A"

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

  1. Automatic Transmission Models:
    Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.
    A115899E19
  1. Manual Transmission Models:
    Vehicles, which are equipped with manual transmission, detect the vehicle speed using the No. 1 vehicle speed sensor. The No. 1 vehicle speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission or transfer output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.
    A115900E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0500
Automatic Transmission Models:
ECM detects following conditions simultaneously 500 times (1 trip detection logic)
  1. No SPD signal from combination meter while ECM detects SP2 (No. 2 speed sensor) signal
  2. Vehicle speed 9 km/h (6 mph) or more for 4 seconds
  3. Park/Neutral position switch OFF (shift lever other than P and N positions)
  4. Transfer lever in other than N position (4WD)
  1. Open or short in speed signal circuit
  2. Hydraulic brake booster (Skid control ECU)
  3. Combination meter
  4. ECM
Manual Transmission Models:
Following conditions met for 5 seconds or more (2 trip detection logic):
  1. Engine coolant temperature 70°C (158°F) or more
  2. Engine speed 1,500 to 4,000 rpm
  3. Fuel cut at high engine speed not executing
  4. Engine load 31.6 % or more
  1. Open or short in speed signal circuit
  2. No. 1 vehicle speed sensor
  3. Combination meter
  4. ECM

MONITOR DESCRIPTION

  1. Automatic Transmission Models:
    The ECM assumes that the vehicle is being driven, while the vehicle speed sensor signal is being transmitted by the combination meter. If there is no signal from the combination meter, despite the ECM detecting the speed signal from the speed sensor No. 2, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets a DTC.
  1. Manual Transmission Models:
    The ECM assumes that the vehicle is being driven, when the indicated engine speed is more than 1,500 rpm and the engine load calculated by the ECM is more than certain level. If there is no signal from the vehicle speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets a DTC.

WIRING DIAGRAM

A226861E08

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on the tester and speedometer display are equal.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM)
E126867E07
  1. Remove the combination meter.

  1. Connect the combination meter connector.

  1. Move the shift lever to neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-14 (+S) - Body ground
    Ignition switch ON
    (turn wheel slowly)
    Voltage generated intermittently

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    *b
    Turn Wheel

    HINT:
    The output voltage should fluctuate up and down similarly to the diagram on the left when the wheel is turned slowly.



NG
GO TO METER / GAUGE SYSTEM (SPEED METER MALFUNCTION) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E13-14 (+S) - E46-8 (SPD)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E13-14 (+S) or E46-8 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM (Click here)


← P0443 Evaporative Emission Control System Purge Control Valve Circuit (from Aug 2009)P0500 Vehicle Speed Sensor "A" (Aug 2009 – Oct 2010) →