P0500 Vehicle Speed Sensor "A"
Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
DESCRIPTION
- Automatic Transmission Models:
Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.


- Manual Transmission Models:
Vehicles, which are equipped with manual Transmission, detect the vehicle speed using the No. 1 vehicle speed sensor. The No. 1 vehicle speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission or transfer output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0500 |
While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic) |
|
*2: for Manual Transmission Models
MONITOR DESCRIPTION
Automatic Transmission Models:The ECM assumes that the vehicle is being driven when the indicated vehicle speed is 9 km/h (5.59 mph) or more. If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
Manual Transmission Models:
The ECM assumes that the vehicle is being driven when the indicated engine speed is 2000 to 5000 rpm and the engine load calculated by the ECM is more than a certain level or the idle fuel-cut operation* is being executed. If there is no signal from the vehicle speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.
*: Idle fuel-cut is executed when the throttle valve is fully closed and engine speed is over 2800 rpm.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
- HINT:
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
- If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
- OK:
- Vehicle speeds displayed on the tester and speedometer display are equal.
|
|
||||
| OK | ||
| ||
| 2. INSPECT COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM) |
![]() ![]() |
Remove the combination meter.
Connect the combination meter connector.
Move the shift lever to neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E13-14 (+S) - Body ground
Ignition switch ON (turn wheel slowly)
Voltage generated intermittently
Text in Illustration *a
Component with harness connected
(ECM)
*b
Turn Wheel
- HINT:
- The output voltage should fluctuate up and down similarly to the diagram on the left when the wheel is turned slowly.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM) |
Disconnect the combination meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
E13-14 (+S) - E82-18 (SPD)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
E13-14 (+S) or E82-18 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||

