P0500 Vehicle Speed Sensor "A"
Diagnostic trouble codes · Vehicles built from Nov 2010
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate to skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0500 |
While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic) |
|
MONITOR DESCRIPTION
Automatic Transmission Models:The ECM assumes that the vehicle is being driven when the vehicle speed measured by the output speed sensor (SP2) is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.
Manual Transmission Models:
The ECM assumes that the vehicle is being driven when the idle fuel-cut operation* is being executed. If there is no signal from the vehicle speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.
*: Idle fuel-cut is executed when the throttle valve is fully closed and engine speed is over 2800 rpm.
WIRING DIAGRAM


INSPECTION PROCEDURE
- Various system use the vehicle speed signal distributed the combination meter. Check all the components possibly related to speed signal.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
- OK:
- The operation of the speedometer is normal.
- HINT:
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
- If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the tester.
- OK:
- Vehicle speeds displayed on the tester and speedometer display are equal.
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM) |
Disconnect the combination meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
E13-14 (+S) - E82-18 (SPD)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
E13-14 (+S) or E82-18 (SPD) - Body ground
Always
10 kΩ or higher
- HINT:
- If the wire has a short, check the speed signal circuit in other system related to the vehicle speed signal (e.g. 4WD control ECU, A/C Amplifier, etc.).
|
|
||||
| OK | |
| 4. INSPECT COMBINATION METER (+S VOLTAGE) |
![]() ![]() |
Disconnect the combination meter connector.
- HINT:
- Disconnect the ECM connectors on the other systems related to the speed signal (but the ECM connectors must be connected).
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E13-14 (+S) - Body ground
Ignition switch ON
4.5 to 5.5 V
| *a |
Front view of wire harness connector (to Combination Meter) |
|
|
||||
| OK | |
| 5. INSPECT COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM) |
![]() ![]() |
Remove the combination meter.
Connect the combination meter connector.
Move the shift lever to neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E13-14 (+S) - Body ground
Ignition switch ON (Turn wheel slowly)
Voltage generated intermittently
Text in Illustration *a
Component with harness connected
(ECM)
*b
Turn Wheel
- HINT:
- The output voltage should fluctuate up and down similarly to the diagram on the left when the wheel is turned slowly.
|
|
||||
| OK | ||
| ||
| 6. INSPECT COMBINATION METER (SPD SIGNAL INPUT WAVEFORM) |
![]() ![]() |
Remove the combination meter.
Connect the combination meter connector.
Move the shift lever to neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E13-13 (SI) - Body ground
Ignition switch ON (Turn wheel slowly)
Voltage generated intermittently
Text in Illustration *a
Component with wire harness connected
(Combination Meter)
*b
Turn Wheel
- HINT:
- The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
Reinstall the combination meter.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (COMBINATION METER - HYDRAULIC BRAKE BOOSTER) |
Disconnect the combination meter connector.
Disconnect the hydraulic brake booster connector.
Measure the resistance according the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
E13-13 (SI) - A4-12 (SP1)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
E13-13 (SI) or A4-12 (SP1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||



