2011-2016 FJ Cruiser · Service Manual ENGINE

P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
When the engine speed is between 2200 rpm and 4100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status), to close the IACV. Under other conditions, the VSV is usually OFF and the IACV is open.
A115903E03
DTC No.
DTC Detection Condition
Trouble Area
P0660
Conditions (a) and (b) are met for 0.5 seconds or more (2 trip detection logic):
(a) The voltage of terminal ACIS of the ECM is low when the VSV is OFF.
(b) The engine has started.
  1. Open or short in VSV for ACIS circuit
  2. VSV for ACIS
  3. ECM

WIRING DIAGRAM

A171632E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR INTAKE CONTROL)
A067588E05
  1. Connect the intelligent tester to the DLC3.

  1. Disconnect the vacuum hose.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control.

  1. Check the VSV operation when it is operated using the intelligent tester.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

  1. Reconnect the vacuum hose.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT VSV FOR ACIS (RESISTANCE)

  1. A152887E04
    Disconnect the VSV for ACIS connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified condition
    1 - 2
    20°C
    33 to 39 Ω

  1. Reconnect the VSV for ACIS connector.



NG
REPLACE VSV FOR ACIS (Click here)
OK


3. INSPECT VSV FOR ACIS (POWER SOURCE)

  1. A107917E35
    Disconnect the VSV for ACIS connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B17-1 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the VSV for ACIS connector.



NG
Go to step 5
OK


4. CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM)

  1. A171631E03
    Disconnect the VSV for ACIS connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance :
    Tester Connection
    Condition
    Specified Condition
    B17-2 - B1-33 (ACIS)
    Always
    Below 1 Ω
    B17-2 or B1-33 (ACIS) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VSV for ACIS connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - EFI NO.2 FUSE - EFI RELAY)

  1. A171630E02
    Inspect the EFI No. 2 fuse.
    1. Remove the EFI No. 2 fuse from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EFI No. 2 fuse
      Always
      Below 1 Ω

    3. Reinstall the EFI No. 2 fuse.

  1. Disconnect the VSV for ACIS connector.

  1. Remove the EFI relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B17-1 - EFI relay(3)
    Always
    Below 1 Ω
    B17-1 or EFI relay(3) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VSV for ACIS connector.

  1. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR AND REPLACE FUSE
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)


← P0617 Starter Relay Circuit High (from Aug 2012)P0724 Brake Switch "B" Circuit High (Jul 2007 – Jul 2009) →