2011-2016 FJ Cruiser · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic)
  1. (a) Vehicle speed more than 20 km/h (12.4 mph)
  2. (b) Engine speed more than 1000 rpm
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch (Automatic Transmission model)
  2. STA relay circuit
  3. Ignition switch
  4. ECM

WIRING DIAGRAM

A226862E03
A133424E04

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START position.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON

    Result 
    Result
    Proceed to
    OK
    A
    NG (Automatic Transmission models)
    B
    NG (Manual Transmission models)
    C



B
Go to step 2

C
Go to step 8
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
C259502E04
  1. Disconnect the Park/Neutral Position (PNP) switch connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned ON.

    Result 
    Starter Signal
    Proceed to
    Remain ON
    A
    OFF
    B
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to PNP Switch)



B
Go to step 4
A


3. INSPECT ECM (STA TERMINAL VOLTAGE)

  1. A226162E04
    Disconnect the B65 Park/Neutral Position (PNP) switch connector.

  1. Disconnect the ECM connector.

Text in Illustration 
*a
Rear view of wire harness connector
(to ECM)
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E81-10 (STA) - Body ground
    Ignition switch ON
    11 to 14 V
    A
    Below 1.5 V
    B



B
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STA RELAY - PARK/NEUTRAL POSITION SWITCH)

4. INSPECT PARK/NEUTRAL POSITION SWITCH
A093221E31
  1. Disconnect the B65 Park/Neutral Position (PNP) switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 - 5
    Shift lever position except P and N
    10 kΩ or higher
    2 - 5
    All shift lever positions (P, R, N, D and S)
    10 kΩ or higher

    Result 
    Result
    Proceed to
    Short between 4 and 5
    A
    Short between 2 and 5
    B
    Within standard range
    C
    Text in Illustration 
    *a
    Component without harness connected
    (PNP Switch)



B
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)

C
Go to step 6
A


5. REPLACE PARK/NEUTRAL POSITION SWITCH
  1. Replace the park/neutral position switch (Click here).


NEXT


6. INSPECT IGNITION SWITCH

  1. A116847E02
    Remove the ignition switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (ST1) - 2 (AM1)
    Ignition switch ON
    10 kΩ or higher
    1 (ST1) - 7 (AM2)
    Ignition switch ON
    10 kΩ or higher



NG
REPLACE IGNITION SWITCH (Click here)
OK


7. INSPECT ECM (NSW TERMINAL VOLTAGE)

  1. A226178E03
    Disconnect the ECM connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    B48-2 (NSW) - Body ground
    Ignition switch ON
    11 to 14 V
    A
    Below 1.5 V
    B



B
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH - ECM)

8. INSPECT IGNITION SWITCH

  1. A116847E02
    Remove the ignition switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (ST1) - 2 (AM1)
    Ignition switch ON
    10 kΩ or higher
    1 (ST1) - 7 (AM2)
    Ignition switch ON
    10 kΩ or higher



NG
REPLACE IGNITION SWITCH (Click here)
OK


9. INSPECT ECM (STA TERMINAL VOLTAGE)

  1. A226162E04
    Disconnect the ECM connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E81-10 (STA) - Body ground
    Ignition switch ON
    11 to 14 V
    A
    Below 1.5 V
    B



B
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - ECM - STA RELAY)


← P0617 Starter Relay Circuit High (Nov 2010 – Jul 2012)P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (Dec 2007 – Jul 2009) →