2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Also covers:

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The front passenger side curtain shield squib circuit consists of the front passenger side - center airbag sensor assembly and the curtain shield airbag assembly.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side curtain shield squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1835/58
  1. Center airbag sensor assembly detects line short circuit signal in front passenger side curtain shield squib circuit 5 times during primary check.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Front passenger side floor wire
  2. Front passenger side - curtain shield airbag assembly (Front passenger side curtain shield squib)
  3. Center airbag sensor assembly
B1836/58
  1. Center airbag sensor assembly detects open circuit signal in front passenger side curtain shield squib circuit for 2 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
B1837/58
  1. Center airbag sensor assembly detects short circuit to ground signal in front passenger side curtain shield squib circuit for 0.5 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
B1838/58
  1. Center airbag sensor assembly detects short circuit to B+ signal in front passenger side curtain shield squib circuit for 0.5 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction

WIRING DIAGRAM

C233203E03
C233203E05

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
  2. After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTORS (FRONT PASSENGER SIDE FLOOR WIRE - FRONT PASSENGER SIDE - CURTAIN SHIELD AIRBAG ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check the front passenger side floor wire connector and terminals (on the front passenger side - curtain shield airbag assembly side) and check that the connector is properly connected to the front passenger side - curtain shield assembly.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE FRONT PASSENGER SIDE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK FRONT PASSENGER SIDE - CURTAIN SHIELD AIRBAG ASSEMBLY (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB)

  1. C135748E03
    Disconnect the connector from the front passenger side - curtain shield airbag assembly.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the front passenger side - curtain shield airbag assembly (front passenger side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1835/58, B1836/58, B1837/58 and B1838/58 are not output.

    HINT:
    DTCs other than B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front Passenger Side Curtain Shield Squib
    *b
    Center Airbag Sensor Assembly
    *c
    Front view of wire harness connector
    (to Front Passenger Side Curtain Shield Squib)
    *d
    Connector C
    *e
    DLC3
    *f
    DTC 58



NG
Go to step 3
OK

REPLACE FRONT PASSENGER SIDE - CURTAIN SHIELD AIRBAG ASSEMBLY (Click here)

3. CHECK CONNECTOR (FRONT PASSENGER SIDE FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check the front passenger side floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE FRONT PASSENGER SIDE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK FRONT PASSENGER SIDE FLOOR WIRE (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB CIRCUIT)

  1. C135749E03
    Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      K5-1 - Body ground
      Ignition switch ON
      Below 1 V
      K5-2 - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      L8-1 - Body ground
      Ignition switch ON
      Below 1 V
      L8-2 - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      K5-1 - K5-2
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      L8-1 - L8-2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      K5-1 - Body ground
      Always
      1 MΩ or higher
      K5-2 - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      L8-1 - Body ground
      Always
      1 MΩ or higher
      L8-2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      K5-1 - K5-2
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      L8-1 - L8-2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector to the original condition.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front Passenger Side Curtain Shield Squib
      *b
      Center Airbag Sensor Assembly
      *c
      Front Passenger Side Floor Wire
      *d
      Front view of wire harness connector
      (to Front Passenger Side Curtain Shield Squib)
      *e
      Connector C



NG
REPLACE FRONT PASSENGER SIDE FLOOR WIRE
OK


5. CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the connectors to the front passenger side - curtain shield airbag assembly and the center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1835/58, B1836/58, B1837/58 and B1838/58 are not output.

    HINT:
    DTCs other than DTC B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit (+ B1836/58, B1837/58, B1838/58) (Jul 2007 – Oct 2010)B1900/73 Short in Front Pretensioner Squib RH Circuit (+ B1901/73, B1902/73, B1903/73) (from Aug 2012) →