2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

Also covers:

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The front passenger side curtain shield squib circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side curtain shield squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1835/58
  1. Center airbag sensor assembly detects line short circuit signal in front passenger side curtain shield squib circuit 5 times during primary check.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Front passenger side curtain shield squib)
  3. Center airbag sensor assembly
B1836/58
  1. Center airbag sensor assembly detects open circuit signal in front passenger side curtain shield squib circuit for 2 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Front passenger side curtain shield squib)
  3. Center airbag sensor assembly
B1837/58
  1. Center airbag sensor assembly detects short circuit to ground signal in front passenger side curtain shield squib circuit for 0.5 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Front passenger side curtain shield squib)
  3. Center airbag sensor assembly
B1838/58
  1. Center airbag sensor assembly detects short circuit to B+ signal in front passenger side curtain shield squib circuit for 0.5 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Curtain shield airbag assembly RH (Front passenger side curtain shield squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C157591E45

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTOR (FLOOR WIRE - CURTAIN SHIELD AIRBAG ASSEMBLY RH)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check the floor wire connector and terminals (on the curtain shield airbag assembly RH side) and check that the connector is properly connected to the curtain shield assembly RH.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB)

  1. C135748E01
    Disconnect the connector from the curtain shield airbag assembly RH.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the curtain shield airbag assembly RH (front passenger side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1835/58, B1836/58, B1837/58 and B1838/58 are not output.

    HINT:
    DTCs other than B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH (Click here)

3. CHECK CONNECTOR (FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check the floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK FLOOR WIRE (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB CIRCUIT)

  1. C135749E01
    Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester connection
      Switch Condition
      Specified condition
      1 - Body ground
      Ignition switch on
      Below 1 V
      2 - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      1 - 2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      1 - Body ground
      Always
      1 MΩ or higher
      2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      1 - 2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector to the original condition.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. H100881E01
    Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1835/58, B1836/58, B1837/58 and B1838/58 are not output.

    HINT:
    DTCs other than DTC B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1835/58 Short in Curtain Shield Squib LH Circuit (+ B1836/58, B1837/58, B1838/58) (from Aug 2012)B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit (+ B1836/58, B1837/58, B1838/58) (Nov 2010 – Jul 2012) →