B1900/73 Short in Front Pretensioner Squib RH Circuit
Diagnostic trouble codes · Vehicles built from Aug 2012
Also covers:
- B1901/73 Open in Front Pretensioner Squib RH Circuit
- B1902/73 Short to GND in Front Pretensioner Squib RH Circuit
- B1903/73 Short to B+ in Front Pretensioner Squib RH Circuit
DESCRIPTION
The front pretensioner squib RH circuit consists of the center airbag sensor assembly and front seat outer belt assembly RH (front pretensioner squib RH).The center airbag sensor assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1900/73 |
|
|
| B1901/73 |
|
|
| B1902/73 |
|
|
| B1903/73 |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
- HINT:
- Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
- After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).
- Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
| 1. CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the front seat outer belt assembly RH (front pretensioner squib RH) and center airbag sensor assembly. Also check that the connectors that link the floor wire and No. 1 rear door wire are properly connected.
- OK:
- The connectors are properly connected.
- HINT:
- If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the front seat outer belt assembly RH (front pretensioner squib RH) and center airbag sensor assembly. Also check that the connectors that link the floor wire and No. 1 rear door wire are properly connected.
Check that the terminals of the connectors are not damaged.
- OK:
- The terminals are not deformed or damaged.
Check that the floor wire connector (on the front seat outer belt assembly RH (front pretensioner squib RH) side) is not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.
- OK:
- The short spring is not deformed or damaged.
|
|
||||
| OK | |
| 2. CHECK FRONT SEAT OUTER BELT ASSEMBLY RH |
- SST
- 09843-18061
Connect the connector to the center airbag sensor assembly.

Connect SST (resistance 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front seat outer belt assembly (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to pretensioner deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting it.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting it.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.
- HINT:
- Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector C.
Text in Illustration *1
Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2
Center Airbag Sensor Assembly
*a
Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))
|
|
||||
| OK | ||
| ||
| 3. CHECK FRONT DRIVER SIDE PRETENSIONER SQUIB CIRCUIT (FLOOR WIRE - NO. 1 REAR DOOR WIRE) |
Disconnect the floor wire from the center airbag sensor assembly.

Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I5-1 (R+) - Body ground
Ignition switch ON
Below 1 V
I5-2 (R-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I5-1 (R+) - I5-2 (R-)
Always
Below 1 Ω
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I5-1 (R+) - Body ground
Always
1 MΩ or higher
I5-2 (R-) - Body ground
Always
1 MΩ or higher
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I5-1 (R+) - I5-2 (R-)
Always
1 MΩ or higher
Restore the released activation prevention mechanism of connector B to the original condition.
Text in Illustration *1
Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2
Center Airbag Sensor Assembly
*a
Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))
|
|
||||
| OK | |
| 4. CHECK DTC |
Connect the connectors to the front seat outer belt assembly RH (front pretensioner squib RH) and center airbag sensor assembly.

Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.
- HINT:
- Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.
Text in Illustration *1
Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2
Center Airbag Sensor Assembly
|
|
||||
| OK | ||
| ||
| 5. CHECK FLOOR WIRE |
Disconnect the floor wire from the center airbag sensor assembly.

Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
KI1-2 (R+) - Body ground
Ignition switch ON
Below 1 V
KI1-1 (R-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
KI1-2 (R+) - KI1-1 (R-)
Always
Below 1 Ω
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
KI1-2 (R+) - Body ground
Always
1 MΩ or higher
KI1-1 (R-) - Body ground
Always
1 MΩ or higher
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
KI1-2 (R+) - KI1-1 (R-)
Always
1 MΩ or higher
Restore the released activation prevention mechanism of connector B to the original condition.
Text in Illustration *1
Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2
Center Airbag Sensor Assembly
*3
No. 1 Rear Door Wire
*4
Floor Wire
*a
Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))
|
|
||||
| OK | ||
| ||
