2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1900/73 Short in Front Driver Side Pretensioner Squib Circuit

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Also covers:

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The driver side front pretensioner squib circuit consists of the center airbag sensor assembly and the driver side - front seat outer belt assembly.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side front pretensioner squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1900/73
  1. Center airbag sensor assembly detects line short circuit signal in driver side front pretensioner squib circuit 5 times during primary check.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Driver side rear door wire
  2. Driver side floor wire
  3. Driver side - front seat outer belt assembly (Driver side front pretensioner squib)
  4. Center airbag sensor assembly
B1901/73
  1. Center airbag sensor assembly detects open circuit signal in driver side front pretensioner squib circuit for 2 seconds.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
B1902/73
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side front pretensioner squib circuit for 0.5 seconds.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
B1903/73
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side front pretensioner squib circuit for 0.5 seconds.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction

WIRING DIAGRAM

C146249E92
C146249E93

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
  2. After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTORS (REAR DOOR WIRE NO. 2 - DRIVER SIDE - FRONT SEAT OUTER BELT ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check the driver side rear door wire connector and terminals (on the driver side - front seat outer belt assembly side) and check that the connector is properly connected to the driver side - front seat outer belt assembly.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE REAR DOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK DRIVER SIDE - FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SIDE FRONT PRETENSIONER SQUIB)

  1. C233314E01
    Disconnect the connector from the driver side - front seat outer belt assembly.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector E.

    CAUTION:
    Never connect a tester to the driver side - front seat outer belt assembly (driver side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1900/73, B1901/73, B1902/73 and B1903/73 are not output.

    HINT:
    DTCs other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Driver Side Front Pretensioner Squib
    *b
    Center Airbag Sensor Assembly
    *c
    Driver Side Rear Door Wire
    *d
    Front view of wire harness connector
    (to Driver Side Front Pretensioner Squib)
    *e
    Connector E
    *f
    DLC3
    *g
    DTC 73



NG
Go to step 3
OK

REPLACE DRIVER SIDE - FRONT SEAT OUTER BELT ASSEMBLY (Click here)

3. CHECK CONNECTOR (DRIVER SIDE FLOOR WIRE - DRIVER SIDE REAR DOOR WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the SST from connector E.

  1. Check the driver side floor wire connector and terminals (on the driver side rear door wire side) and check that the connector is properly connected to the driver side rear door wire.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK DRIVER SIDE REAR DOOR WIRE
  1. Disconnect the driver side floor wire connector from the driver side rear door wire.

  1. C233315E01
    Check for short to B+ in the circuit.
    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      J6-1 - Body ground
      Ignition switch ON
      Below 1 V
      J6-2 - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      I4-1 - Body ground
      Ignition switch ON
      Below 1 V
      I4-2 - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      J6-1 - J6-2
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      I4-1 - I4-2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      J6-1 - Body ground
      Always
      1 MΩ or higher
      J6-2 - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      I4-1 - Body ground
      Always
      1 MΩ or higher
      I4-2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector C (Click here ).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      J6-1 - J6-2
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      I4-1 - I4-2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Driver Side Front Pretensioner Squib
      *b
      Center Airbag Sensor Assembly
      *c
      Driver Side Rear Door Wire
      *d
      Front view of wire harness connector
      (to Driver Side Front Pretensioner Squib)
      *e
      Connector E



NG
REPLACE DRIVER SIDE REAR DOOR WIRE
OK


5. CHECK CONNECTOR (DRIVER SIDE FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Check the driver side floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


6. CHECK DRIVER SIDE FLOOR WIRE
C233316E01
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      LJ1-1 - Body ground
      Ignition switch ON
      Below 1 V
      LJ1-2 - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      KI1-1 - Body ground
      Ignition switch ON
      Below 1 V
      KI1-2 - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      LJ1-1 - LJ1-2
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      KI1-1 - KI1-2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      LJ1-1 - Body ground
      Always
      1 MΩ or higher
      LJ1-2 - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      KI1-1 - Body ground
      Always
      1 MΩ or higher
      KI1-2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      LJ1-1 - LJ1-2
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      KI1-1 - KI1-2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Driver Side Front Pretensioner Squib
      *b
      Center Airbag Sensor Assembly
      *c
      Driver Side Floor Wire
      *d
      Front view of wire harness connector
      (Driver Side Floor Wire)
      *e
      Connector C



NG
REPLACE DRIVER SIDE FLOOR WIRE
OK


7. CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the driver side floor wire connector to the driver side rear door wire.

  1. Connect the connectors to the driver side - front seat outer belt assembly and the center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1900/73, B1901/73, B1902/73 and B1903/73 are not output.

    HINT:
    DTCs other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Jul 2007 – Oct 2010)B1905/74 Short in Front Pretensioner Squib LH Circuit (+ B1906/74, B1907/74, B1908/74) (from Aug 2012) →