2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1900/73 Short in Front Driver Side Pretensioner Squib Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

Also covers:

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The driver side front pretensioner squib circuit consists of the center airbag sensor assembly and the front seat outer belt assembly LH.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side front pretensioner squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1900/73
  1. Center airbag sensor assembly detects line short circuit signal in driver side front pretensioner squib circuit 5 times during primary check.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Rear door wire No.2
  2. Floor wire No.2
  3. Front seat outer belt assembly LH (Driver side front pretensioner squib)
  4. Center airbag sensor assembly
B1901/73
  1. Center airbag sensor assembly detects open circuit signal in driver side front pretensioner squib circuit for 2 seconds.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Rear door wire No.2
  2. Floor wire No.2
  3. Front seat outer belt assembly LH (Driver side front pretensioner squib)
  4. Center airbag sensor assembly
B1902/73
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side front pretensioner squib circuit for 0.5 seconds.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Rear door wire No.2
  2. Floor wire No.2
  3. Front seat outer belt assembly LH (Driver side front pretensioner squib)
  4. Center airbag sensor assembly
B1903/73
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side front pretensioner squib circuit for 0.5 seconds.
  2. Driver side front pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Rear door wire No.2
  2. Floor wire No.2
  3. Front seat outer belt assembly LH (Driver side front pretensioner squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C146249E33

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTOR (REAR DOOR WIRE NO.2 - FRONT SEAT OUTER BELT ASSEMBLY LH)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check the rear door wire No.2 connector and terminals (on the front seat outer belt assembly LH side) and check that the connector is properly connected to the front seat outer belt assembly LH.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE REAR DOOR WIRE NO.2

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (DRIVER SIDE FRONT PRETENSIONER SQUIB)

  1. C135751E01
    Disconnect the connector from the front seat outer belt assembly LH.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector E.

    CAUTION:
    Never connect a tester to the front seat outer belt assembly LH (driver side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1900/73, B1901/73, B1902/73 and B1903/73 are not output.

    HINT:
    DTCs other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)

3. CHECK CONNECTOR (FLOOR WIRE NO.2 - REAR DOOR WIRE NO.2)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector E.

  1. Check the floor wire No.2 connector and terminals (on the rear door wire No.2 side) and check that the connector is properly connected to the rear door wire No.2.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE FLOOR WIRE NO.2

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK REAR DOOR WIRE NO.2
  1. Disconnect the floor wire No.2 connector from the rear door wire No.2.

  1. C135752E01
    Check for short to B+ in the circuit.
    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      1 - Body ground
      Ignition switch on
      Below 1 V
      2 - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - Body ground
      Always
      1 MΩ or higher
      2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector C (Click here ).

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPAIR OR REPLACE REAR DOOR WIRE NO.2
OK


5. CHECK CONNECTOR (FLOOR WIRE NO.2 - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Check the floor wire No.2 connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE FLOOR WIRE NO.2

C
CONNECT CONNECTOR PROPERLY
A


6. CHECK FLOOR WIRE NO.2
C135750E02
  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      1 - Body ground
      Ignition switch on
      Below 1 V
      2 - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - Body ground
      Always
      1 MΩ or higher
      2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK


7. CHECK CENTER AIRBAG SENSOR ASSEMBLY
C127740E01
  1. Connect the floor wire No.2 connector to the rear door wire No.2 LH.

  1. Connect the connectors to the front seat outer belt assembly LH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1900/73, B1901/73, B1902/73 and B1903/73 are not output.

    HINT:
    DTCs other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1900/73 Short in Front Pretensioner Squib RH Circuit (+ B1901/73, B1902/73, B1903/73) (from Aug 2012)B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Nov 2010 – Jul 2012) →