B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Also covers:
- B1906/74 Open in Front Passenger Side Pretensioner Squib Circuit
- B1907/74 Short to GND in Front Passenger Side Pretensioner Squib Circuit
- B1908/74 Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012
DESCRIPTION
The front passenger side front pretensioner squib circuit consists of the center airbag sensor assembly and the front passenger side - front seat outer belt assembly.This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side front pretensioner squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1905/74 |
|
|
| B1906/74 |
|
|
| B1907/74 |
|
|
| B1908/74 |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
- After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
| 1. CHECK CONNECTORS (FRONT PASSENGER SIDE REAR DOOR WIRE - FRONT PASSENGER SIDE - FRONT SEAT OUTER BELT ASSEMBLY) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check the front passenger side rear door wire connector and terminals (on the front passenger side - front seat outer belt assembly side) and check that the connector is properly connected to the front passenger side - front seat outer belt assembly.
Result Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK FRONT PASSENGER SIDE - FRONT SEAT OUTER BELT ASSEMBLY (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB) |
Disconnect the connectors from the front passenger side - front seat outer belt assembly.

Connect the black wire side of SST (resistance 2.1 Ω) to connector E.
- CAUTION:
- Never connect a tester to the front passenger side - front seat outer belt assembly (front passenger side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- Insert the SST straight into the terminals of the connector.
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1905/74, B1906/74, B1907/74 and B1908/74 are not output.
- HINT:
- DTCs other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.
Text in Illustration *A
for LHD
*B
for RHD
*a
Front Passenger Side Front Pretensioner Squib
*b
Center Airbag Sensor Assembly
*c
Front view of wire harness connector
(to Front Passenger Side Front Pretensioner Squib)
*d
Connector E
*e
DLC3
*f
DTC 74
|
|
||||
| OK | ||
| ||
| 3. CHECK CONNECTOR (FRONT PASSENGER SIDE FLOOR WIRE - FRONT PASSENGER SIDE REAR DOOR WIRE) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the SST from connector E.
Check the front passenger side floor wire connector and terminals (on the front passenger side rear door wire side) and check that the connector is properly connected to the front passenger side rear door wire.
Result Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK FRONT PASSENGER SIDE REAR DOOR WIRE |
Disconnect the front passenger side floor wire connector from the front passenger side rear door wire.
Check for short to B+ in the circuit.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
I4-1 - Body ground
Ignition switch ON
Below 1 V
I4-2 - Body ground
Ignition switch ON
Below 1 V
- for RHD:
Tester Connection
Switch Condition
Specified Condition
J4-1 - Body ground
Ignition switch ON
Below 1 V
J4-2 - Body ground
Ignition switch ON
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
I4-1 - I4-2
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
J4-1 - J4-2
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
I4-1 - Body ground
Always
1 MΩ or higher
I4-2 - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
J4-1 - Body ground
Always
1 MΩ or higher
J4-2 - Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector D (Click here ).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
I4-1 - I4-2
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
J4-1 - J4-2
Always
1 MΩ or higher
Restore the released activation prevention mechanism of connector D to the original condition.
Text in Illustration *A
for LHD
*B
for RHD
*a
Front Passenger Side Front Pretensioner Squib
*b
Center Airbag Sensor Assembly
*c
Front Passenger Side Rear Door Wire
*d
Front view of wire harness connector
(to Front Passenger Side Front Pretensioner Squib)
*e
Connector E
|
|
||||
| OK | |
| 5. CHECK CONNECTOR (FRONT PASSENGER SIDE FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY) |
Check the front passenger side floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.
Result Result
Proceed to
No problem.
A
Connector or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 6. CHECK FRONT PASSENGER SIDE FLOOR WIRE |
Disconnect the connectors from the center airbag sensor assembly.

Check for short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
KI1-1 - Body ground
Ignition switch ON
Below 1 V
KI1-2 - Body ground
Ignition switch ON
Below 1 V
- for RHD:
Tester Connection
Switch Condition
Specified Condition
LJ1-1 - Body ground
Ignition switch ON
Below 1 V
LJ1-2 - Body ground
Ignition switch ON
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
KI1-1 - KI1-2
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
LJ1-1 - LJ1-2
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
KI1-1 - Body ground
Always
1 MΩ or higher
KI1-2 - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
LJ1-1 - Body ground
Always
1 MΩ or higher
LJ1-2 - Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
KI1-1 - KI1-2
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
LJ1-1 - LJ1-2
Always
1 MΩ or higher
Restore the released activation prevention mechanism of connector B to the original condition.
Text in Illustration *A
for LHD
*B
for RHD
*a
Front Passenger Side Front Pretensioner Squib
*b
Center Airbag Sensor Assembly
*c
Front Passenger Side Rear Door Wire
*d
Front Passenger Side Floor Wire
*e
Front view of wire harness connector
(Front Passenger Side Floor Wire)
*f
Connector C
|
|
||||
| OK | |
| 7. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the front passenger side floor wire connector to the front passenger side rear door wire.
Connect the connectors to the front passenger side - front seat outer belt assembly and the center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1905/74, B1906/74, B1907/74 and B1908/74 are not output.
- HINT:
- DTCs other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
