2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1662/45 Indicator Light Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

The indicator light circuit consists of the center airbag sensor assembly and the combination meter. DTC B1662/45 is set when a malfunction is detected in the indicator light circuit.
DTC No.
Detection Condition
Trouble Area
B1662/45
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in indicator light circuit for 2 seconds
  2. Indicator light circuit malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Combination meter
  3. Center airbag sensor assembly

WIRING DIAGRAM

C192795E02

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch to the lock position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector and terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - COMBINATION METER)
  1. Disconnect the instrument panel wire connector from the combination meter assembly.

  1. Check the instrument panel wire connector and terminals (on the combination meter side) and check that the connector is properly connected to the combination meter.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector and terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


3. CHECK INSTRUMENT PANEL WIRE
C192796E01
  1. Disconnect the connectors from the center airbag sensor assembly and combination meter assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E13-6 (SW) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E13-6 (SW) - E29-11 (LA)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E13-6 (SW) - Body ground
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


4. CHECK SRS WARNING LIGHT CIRCUIT

  1. C192797E01
    Connect the instrument panel wire to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E13-6 (SW) - Body ground
    1. For 6 seconds after ignition switch turned ON.
    1. Below 1 V
    1. After 6 seconds have passed since ignition switch turned ON.
    1. 11 to 14 V



NG
Go to step 5
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C192787E02
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.

  1. Connect the connectors to the center airbag sensor assembly and the combination meter.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1662/45 is not output.

    HINT:
    DTCs other than B1662/45 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1661/44 Roll Over Cut Off Indicator Malfunction (from Aug 2008)B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (from Aug 2008) →