2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1661/44 Roll Over Cut Off Indicator Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

The curtain airbag cutoff switch is a mechanism that operates both the right and left side of the curtain shield airbag and the front seat outer belt when the center airbag sensor detects a rollover.
The RSCA OFF indicator is installed in the combination meter.
If the curtain airbag cutoff switch is operated, the indicator comes on to inform the driver that the rollover detection system is not working.
The initial setting of the rollover detection system is on. It automatically operates every time the ignition switch is turned ON.
DTC No.
Detection Condition
Trouble Area
B1661/44
  1. The center airbag sensor receives an open signal or short to ground in the RSCA OFF indicator circuit.
  2. RSCA OFF indicator malfunction
  3. Center airbag sensor malfunction
  1. Combination meter assembly (RSCA OFF indicator)
  2. Center airbag sensor assembly
  3. Instrument panel wire

WIRING DIAGRAM

C192790E01

INSPECTION PROCEDURE


1. CHECK RSCA OFF INDICATOR OPERATION
C192791E01
  1. Turn the ignition switch to ON.

  1. Check the RSCA OFF indicator operation.

    Result 
    RSCA OFF Indicator Illumination
    Proceed to
    Always ON
    A
    OFF
    B



B
Go to step 6
A


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the combination meter assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the combination meter assembly.

  1. Check that the connectors (on the center airbag sensor assembly side and combination meter assembly side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK COMBINATION METER ASSEMBLY (RSCA OFF INDICATOR)
C192791E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the RSCA OFF indicator operation.

    Result 
    RSCA OFF Indicator Illumination
    Proceed to
    ON
    A
    OFF
    B



B
Go to step 11
A


5. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - COMBINATION METER)
C192792E01
  1. Disconnect the connector from the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-15 (RMIL) - Body ground
    Ignition Switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-15 (RMIL) - E13-19 (R/O)
    Always
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-15 (RMIL) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

6. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the combination meter assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


7. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor assembly and the combination meter assembly.

  1. Check that the connectors (on the center airbag sensor assembly side and combination meter assembly side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - COMBINATION METER)
C192792E01
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Disconnect the connector from the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-15 (RMIL) - Body ground
    Ignition Switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-15 (RMIL) - E13-19 (R/O)
    Always
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E29-15 (RMIL) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


9. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
C192793E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-2 (IG+) - Body ground
    Ignition Switch ON
    11 to 14 V



NG
REPAIR OR REPLACE POWER SOURCE CIRCUIT
OK


10. CHECK COMBINATION METER ASSEMBLY (RSCA OFF INDICATOR)
C192794E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the combination meter assembly.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Using a service wire, connect E13-21 (ES) and E13-19 (R/O) of the combination meter assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the RSCA OFF indicator operation.

    OK:
    RSCA OFF indicator comes on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


11. CHECK CENTER AIRBAG SENSOR ASSEMBLY
C192787E03
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) battery terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connectors to the center airbag sensor assembly.

  1. Connect the connector to the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1661/44 is not output.

    HINT:
    DTCs other than B1661/44 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (from Aug 2008)B1662/45 Indicator Light Circuit Malfunction (from Aug 2008) →