DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built Aug 2011 – Jul 2012
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012
| BUS CHECK (COMMUNICATION MALFUNCTION ECU) |
- HINT:
- Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.
Select "Bus Check" from the "System Select" screen on the intelligent tester.

Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

Select the system of the DTC to be checked and select "Details".

CAN communication system DTCs are displayed.

| BUS CHECK (COMMUNICATION BUS CHECK) |
- HINT:
- The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.
Select "Communication Bus Check" from the "Bus Check" screen.

The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

- HINT:
- If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).
-
The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop down list. The drop down list displays "ALL", "V Bus", and the names of the remaining buses.

Combo Box
Display Content
ALL
All ECUs (sensors) connected to the CAN bus
V Bus
ECUs (sensors) connected to the V bus
Bus Name
ECUs (sensors) connected to the selected bus
- The connection status (shown below) is indicated by the background color displayed behind the system name.
ECU (Sensor) on V Bus
ECU (Sensor) with no Data Monitor HistoryBackground Color
Connection Status
White
Detected normally
Yellow
Could not be detected in the past, but is currently detected
Red
Detected in the past, but cannot be detected now
Not displayed
Has never been detected
ECU (Sensor) with no Data Monitor HistoryBackground Color
Connection Status
White
Detected normally
Yellow
Could not be detected in the past, but is currently detected
Red
Detected in the past, but cannot be detected now
Not displayed
Has never been detected
Background Color
Connection Status
White
Detected normally
Yellow
Could not be detected in the past, but is currently detected
Red
Detected in the past, but cannot be detected now
Red
Has never been detected but has connection history
Not displayed
Has never been detected and has no connection history
- If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).
"There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.

| CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION |
Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.
ECU/Sensor Name
Intelligent Tester Display
Check method
Airbag Sensor Sssembly
Airbag
Installed on all vehicles
Combination Meter ECU
Combination Meter
Installed on all vehicles
ECM
ECM (Engine)
Installed on all vehicles
Skid Control ECU
Skid Control (ABS/VSC/TRAC)
Installed on all vehicles
Steering Angle Sensor
Spiral Cable (Steering Angle Sensor)
Installed on all vehicles
Yaw Rate Sensor
Yaw Rate / Deceleration Sensor
Installed on all vehicles
| DTC TABLE BY ECU |
- HINT:
- In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the intelligent tester.
- If CAN communication system DTCs are output, trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How To Proceed with Troubleshooting" (Click here).
- In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the intelligent tester.
SKID CONTROL ECU
- HINT:
- DTC communication uses the SIL Line.
DTC No.
Detection Item
U0073
Control Module Communication Bus OFF
U0100
Lost Communication with ECM / PCM "A"
U0126
Lost Communication with Steering Angle Sensor Module
U0123
Lost Communication with Yaw Rate Sensor Module
U0124
Lost Communication with Lateral Acceleration Sensor Module
COMBINATION METER ECU
- HINT:
- DTC communication uses the CAN communication system.
DTC No.
Detection Item
U0100
Lost Communication with ECM / PCM "A"
U0129
Lost Communication with Skid Control ECU
U0151
Lost Communication with Airbag ECU
YAW RATE SENSOR
- HINT:
- The yaw rate sensor is connected to the CAN communication system but CAN communication DTCs are not output.
- If "Yaw Rate/Deceleration Sensor" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Yaw Rate Sensor Communication Stop Mode" (Click here).
- The yaw rate sensor is connected to the CAN communication system but CAN communication DTCs are not output.
STEERING ANGLE SENSOR
- HINT:
- The steering sensor is connected to the CAN communication system but CAN communication DTCs are not output.
- If "Spiral cable (Steering Angle Sensor)" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Steering Angle Sensor Communication Stop Mode" (Click here).
- The steering sensor is connected to the CAN communication system but CAN communication DTCs are not output.
ECM
- HINT:
- The ECM is connected to the CAN communication system but CAN communication DTCs are not output.
- If "ECM (Engine)" is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "ECM Communication Stop Mode" (Click here).
- The ECM is connected to the CAN communication system but CAN communication DTCs are not output.
AIRBAG SENSOR ASSEMBLY
- HINT:
- The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not output.
- If "Airbag " is not displayed on the "Bus Check" screen on the intelligent tester, proceed to "Center Airbag Sensor Communication Stop Mode" (Click here).
- The airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not output.
| DTC COMBINATION TABLE |
| Output from |
Output DTC |
Detected Communication Stop Mode |
|||||
| V-Bus | |||||||
| ECM Communication Stop Mode |
Skid Control ECU Communication Stop Mode |
Yaw Rate Sensor Communication Stop Mode |
Steering Angle Sensor Communication Stop Mode |
Center Airbag Sensor Communication Stop Mode |
Combination Meter ECU Communication Stop Mode |
||
| Skid Control ECU |
U0073 |
X |
○*1 |
○ |
○ |
X |
X |
| U0100 |
○ |
○*1 |
X |
X |
X |
X |
|
| U0126 |
X |
○*1 |
X |
○ |
X |
X |
|
| U0123 |
X |
○*1 |
○ |
X |
X |
X |
|
| U0124 |
X |
○*1 |
○ |
X |
X |
X |
|
| Combination Meter ECU |
U0100 |
○ |
X |
X |
X |
X |
○*1 |
| U0129 |
X |
○ |
X |
X |
X |
○*1 |
|
| U0151 |
X |
X |
X |
X |
○ |
○*1 |
|
- HINT:
- ○:Stored.
- X: When one side of branch wire is open, storage may occur.
- *1: DTC may not be output when the CAN communication system malfunctions.
- ○:Stored.
Perform troubleshooting according to the combination of DTCs output.
- HINT:
- Skid Control ECU Communication Stop Mode: (Click here)
- ECM Communication Stop Mode: (Click here)
- Yaw Rate Sensor Communication Stop Mode: (Click here)
- Steering Angle Sensor Communication Stop Mode: (Click here)
- Combination Meter ECU Communication Stop Mode: (Click here)
- Center Airbag Sensor Communication Stop Mode: (Click here)
- Skid Control ECU Communication Stop Mode: (Click here)