ABS Warning Light Remains ON
Circuit diagnosis · Vehicles built from Aug 2011
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011
DESCRIPTION
If any of the following is detected, the ABS warning light remains on.- The skid control ECU connectors are disconnected from the skid control ECU.
- There is a malfunction in the skid control ECU internal circuit.
- There is an open in the harness between the combination meter and skid control ECU.
- The anti-lock brake system is defective.
- The voltage at terminal IG1 is high.
- The rear differential is locked.*
- HINT:
- It may not be possible to use the intelligent tester when the skid control ECU is abnormal.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check the skid control ECU connector connection.
- OK:
- The connector is securely connected.
|
|
||||
| OK | |
| 2. CHECK DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 3. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item : Range
Normal Condition
Diagnostic Note
IG1 Voltage Value
IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
11 to 14 V
Changes in proportion to battery voltage
Measure the voltage output from the ECU displayed on the tester.
Result Result
Proceed
Data display is within Normal Condition
A
Data display is not within Normal Condition
B
|
|
||||
| OK | |
| 5. INSPECT SKID CONTROL ECU (EXI3 TERMINAL) |
for w/ Rear Differential Lock
Disconnect the A4 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
w/ Rear Differential Lock: Rear differential free
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
for w/o Rear Differential Lock
Disconnect the A4 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
Result Result
Proceed to
OK
A
NG (for w/ Rear Differential Lock)
B
NG (for w/o Rear Differential Lock)
C
|
|
||||
|
|
||||
| A | |
| 6. READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light/ ON or OFF
ON: warning on
OFF: warning off
-
Result Result
Proceed to
ABS Warning light remains on, Data Monitor is on.
A
ABS Warning light remains on, Data Monitor is off.
B
|
|
||||
| A | ||
| ||
| 7. INSPECT SKID CONTROL ECU (IG1 TERMINAL) |
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
A4-46 (IG1) - Body ground
Idling
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | |
| 8. INSPECT SKID CONTROL ECU (GND TERMINAL) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-1 (GND1) - Body ground
Always
Below 1 Ω
A4-32 (GND2) - Body ground
Always
Below 1 Ω
A5-4 (GND3) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT) |
Disconnect the A4 skid control ECU connector.
Disconnect the L7 four wheel drive control ECU connector.
Disconnect the D2 rear differential lock indicator switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-40 (EXI3) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 10. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH) |
Remove the rear differential lock detection switch (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
2 - 1
Pushed in
Below 1 Ω
Not pushed in
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Differential Lock Indicator Switch)
|
|
||||
| OK | |
| 11. INSPECT SKID CONTROL ECU (EXI3 TERMINAL) |
Disconnect the A4 skid control ECU connector.
Connect the L7 four wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-40 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | ||
| ||
