2011-2016 FJ Cruiser · Service Manual BRAKE

DTC CHECK / CLEAR

Troubleshooting · Vehicles built Aug 2008 – Jul 2009

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


DTC CHECK (for Using an Intelligent Tester)
  1. Check DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Select the following menu items: Chassis / ABS/VSC/TRC / Trouble Codes
      Read the DTCs by following the prompts on the intelligent tester.


DTC CLEAR (for Using an Intelligent Tester)
  1. Clear DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Select the following menu items: Chassis / ABS/VSC/TRC / Trouble Codes
      Clear the DTCs by following the prompts on the intelligent tester.


DTC CHECK (for Using SST Check Wire)

  1. Check DTCs.

    1. H102392E73
      Using SST, connect terminals TC and CG of the DLC3.
      SST
      09843-18040  

    2. Turn the ignition switch to ON.

    3. Read 2-digit DTCs by observing the blinking of the ABS warning light and the VSC TRC warning light (*1) or SLIP indicator light (*2) on the combination meter.

      HINT:
      1. If no code appears, inspect the ABS warning light circuit, VSC TRC warning light circuit (*1), SLIP indicator circuit (*2) or TC and CG terminal circuit.
        *1: w/o VSC OFF Switch
        *2: w/ VSC OFF Switch
        Trouble Area
        See page
        ABS warning light circuit
        Click here
        Click here
        VSC TRC warning light circuit (*1)
        Click here
        Click here
        SLIP indicator light circuit (*2)
        Click here
        Click here
        TC and CG terminal circuit
        Click here

      2. As an example, the blinking patterns of the normal system indication and DTCs 11 and 21 are shown below.

        F100113E07
      3. DTCs are explained in DTC chart (Click here).

    4. After completing the check, disconnect SST from terminals TC and CG of the DLC3, and turn the ignition switch off.
      If 2 or more malfunctions are detected at the same time, the lowest numbered DTC is displayed first.


DTC CLEAR (for Using SST Check Wire)

  1. Clear DTCs.

    1. H102392E73
      Using SST, connect terminals TC and CG of the DLC3.

    2. Turn the ignition switch to ON.

      SST
      09843-18040  

    3. C139131
      Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    4. Check that the ABS warning light and VSC TRC warning light (*1) or SLIP indicator light (*2) blink in normal code pattern.

    5. Remove SST from the terminals of the DLC3.

    6. Turn the ignition switch off.
      *1: w/o VSC OFF Switch
      *2: w/ VSC OFF Switch

      HINT:
      Clearing the DTCs cannot be performed by removing the battery cable.


END OF DTC CHECK/CLEAR
  1. Turn the ignition switch to ON.

  2. Check that the ABS warning light and VSC TRC warning light (*1) or SLIP indicator light (*2) go off within approximately 3 seconds.

  3. Turn the ignition switch off.
    *1: w/o VSC OFF Switch
    *2: w/ VSC OFF Switch

← DTC CHECK / CLEAR (Jul 2007 – Jul 2008)DTC CHECK / CLEAR (Aug 2009 – Oct 2010) →